REAR SEAT CUSHION HEATER (for 60/40 Split Seat Type 60 Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.


  1. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY


    1. A01ES0LE01

      Set the rear seat cushion heater assembly with the name stamp side facing the seat cushion cover.

    2. Install the rear seat cushion heater assembly with new tack pins.

  2. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    A01ENLEE01

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01ES07E01

      Attach the 3 pieces of fastening tape.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A01EQVH

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A01ER2U

        Connect the 2 seat heater connectors.

    4. Attach the side airbag wire harness clamps.

  4. CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A01EN0JE01

    1. Connect the belt anchor.

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

  5. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    A01EN7EE01

    1. Install the belt with the bolt.

      Torque:
      42 N*m  { 4287 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

      Tech Tips

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.

  6. INSTALL REAR SEAT UNDER TRAY COVER LH

    A01EO07

    1. Install the cover with the 2 screws.

  7. INSTALL REAR SEAT CUSHION COVER RH

    A01ERSG

    1. Attach the 2 claws to install the cover.

    2. Install the 4 screws.

  8. INSTALL REAR UNDER SIDE COVER LH

    A01ERPJ

    1. Attach the 2 claws and 2 clips to install the cover.

    2. Install the 5 screws.

    3. A01EQDR

      Attach the 10 claws.

  9. INSTALL REAR SEATBACK STAY COVER LH

    A01EOZA

    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  10. INSTALL SEAT BELT ANCHOR COVER CAP


    1. A01ER1C

      Install the anchor cover cap with the screw.

    2. A01ESGT

      Attach the claw to close the cap.

  11. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

    A01EOO8

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  12. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A01EOCH

      Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Attach the wire harness clamp.

    3. w/ Seat Heater System:

      Attach the wire harness clamp.

  13. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach the 2 claws to close the protector.

    2. A01ES77

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A01ESK0

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  14. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A01ERC0

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A01EP94

      Attach the 4 claws to install the seat leg side cover.

    3. Install the 4 screws.

  15. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A01EQ9K

    1. Attach the 2 claws to install the cover.

  16. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01EO0H

    1. Attach the 2 claws to install the cover.

  17. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A01EN86

    1. Attach the claw to install the cover.

    2. Install the screw.

  18. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A01EQ7FE01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  19. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

    A01EQQW

    1. Install the release handle with the screw.

  20. INSTALL SEAT ADJUSTER BOLT COVER

    A01ERJV

    1. Attach the 2 claws to install the cover.

  21. INSTALL REAR NO. 1 SEAT ASSEMBLY


    1. Install the rear No. 1 seat assembly Click here.