REAR SEAT CUSHION HEATER (for 60/40 Split Seat Type 40 Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.


  1. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY


    1. A01EPQNE01

      Set the rear seat cushion heater assembly with the name stamp side facing the seat cushion cover.

    2. Install the rear seat cushion heater assembly with new tack pins.

  2. INSTALL REAR SEPARATE TYPE SEAT CUSHION COVER

    A01EQFPE01

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01EQI2E01

      Attach the 3 pieces of fastening tape.

  3. INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seat cushion cover with pad.

    2. Pass the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A01EPNC

        Pass the seatback heater wire harness through the hole in the seat cushion.

      2. A01EN8W

        Connect the 2 seat heater connectors.

    4. Attach the side airbag wire harness clamps.

  4. INSTALL REAR SEAT UNDER TRAY COVER RH

    A01EO07

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  5. INSTALL REAR UNDER SIDE COVER LH

    A01ER6F

    1. Attach the 2 claws and clip to install the cover.

    2. Install the 5 screws.

  6. INSTALL REAR SEAT COVER

    A01EN9A

    1. Attach the 2 claws to install the cover.

    2. Install the 3 screws.

    3. A01EO6N

      Attach the 12 claws.

  7. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

    A01EOO8

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  8. INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH

    A01EO5L

    1. Install the hinge with the 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  9. INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach the 2 claws to close the protector.

    2. A01EQUJ

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A01EQH9

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  10. INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A01ENVE

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A01ENX8

      Attach the 3 claws to install the seat leg side cover.

    3. Install the 4 screws.

  11. INSTALL UPPER SEAT TRACK RAIL COVER RH

    A01ER9T

    1. Attach the 2 claws to install the cover.

  12. INSTALL UPPER SEAT TRACK RAIL COVER LH

    A01EOIJ

    1. Attach the 2 claws to install the cover.

  13. INSTALL REAR NO. 1 SEAT RECLINING COVER LH

    A01EOW4

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  14. INSTALL REAR NO. 1 SEAT RECLINING COVER RH

    A01ERDPE01

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  15. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

    A01EN0M

    1. Install the release handle with the screw.

  16. INSTALL SEAT ADJUSTER BOLT COVER

    A01ER8K

    1. Attach the 2 claws to install the cover.

  17. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    1. Install the rear No. 1 seat assembly Click here.