FRONT SEAT OUTER BELT ASSEMBLY INSTALLATION

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY

    A01EQQOE01

    1. Align the anchor plate positioning hole with the claw, and install the anchor plate with the 2 bolts.

      Tech Tips

      First install the lower bolt, and then install the upper bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  2. INSTALL FRONT SEAT OUTER BELT ASSEMBLY

    A01EP9NE01

    Note

    When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.


    1. Align the claws of the vehicle with the seat belt retractor positioning holes.

    2. Install the seat belt with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
    3. A01EN08E01

      Connect the pretensioner connector labeled A as shown in the illustration.

    4. Connect the tension reducer connector labeled B.

    5. w/ Pre-Crash Safety System:

      Connect the pre-crash safety system connector labeled C.

    6. A01ENDK

      Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL CENTER PILLAR GARNISH

    A01EP32

    1. Pass the seat belt anchor through the center pillar garnish.

    2. Attach the 2 clips and 2 guides to install the center pillar garnish.

    3. Install the bolt.

  4. INSTALL REAR ASSIST GRIP ASSEMBLY

    A01ERXY

    Tech Tips

    Use the same procedure to install the rear assist grip on the other side.


    1. Attach the 2 claws to install the rear assist grip.

    2. Install the 2 bolts.

    3. A01EPZ8

      Attach the 4 claws to install the 2 assist grip plugs.

  5. INSTALL CENTER LOWER PILLAR GARNISH

    A01EOZX

    Tech Tips


    • When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. Attach the 2 claws and 7 clips to install the center lower pillar garnish.

    2. A01EPOZ

      Install the seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  6. INSTALL CENTER PILLAR GARNISH COVER

    Tech Tips


    • When installing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. A01EPVK

      Attach the 2 clips and 2 guides to install the cover.

  7. INSTALL REAR DOOR SCUFF PLATE

    A01EPV0

    1. Attach the 3 clips to install the rear door scuff plate outside.

  8. INSTALL REAR STEP COVER

    Tech Tips

    Use the same procedure to install the step cover on the other side.


    1. A01EQ9D

      w/o Illumination Type Front Door Scuff Plate:

      Attach the 2 claws to install the step cover.

    2. A01EQ94

      w/ Illumination Type Front Door Scuff Plate:

      Attach the 4 claws to install the step cover.

  9. INSTALL FRONT DOOR SCUFF PLATE

    A01EQ14

    1. w/o Illumination:


      1. Attach the 7 claws and 4 clips to install the scuff plate.

    2. A01EOWQ

      w/ Illumination:


      1. Connect the connector.

      2. Attach the 7 claws and 4 clips to install the scuff plate.

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.