LUMBAR SUPPORT ADJUSTER ASSEMBLY INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH
1. Install the lumbar support adjuster LH with the 2 screws.
2. Connect the connector.
3. Text in Illustration
  
  *1 Cable Clamp
  
  *2 Hook
  
  Attach the 4 hooks to install the seatback spring.
4. Install the 4 springs.
5. Connect the active headrest cable to the seatback spring with the cable clamp.

Text in Illustration
*1	Cable Clamp
*2	Hook

INSTALL FRONT SEATBACK PROTECTOR

Text in Illustration
*A	w/ Rear Seat Entertainment System
*1	Double-sided tape

Apply double-sided tape as shown in the illustration.
Install the front seatback protector.

INSTALL SEATBACK COVER WITH PAD

Text in Illustration
*1	Hog Ring
*2	Hog Ring Pliers

Attach the hooks to install the seatback cover with pad.

Text in Illustration
*1	Seatback Cover Bracket
*2	Side Airbag Strap

Attach the seatback cover bracket with the nut.

Torque:: 5.0 N*m { 51 kgf*cm, 44 in.*lbf }

CAUTION:

After the front separate type seatback cover is assembled, make sure the side airbag strap is not twisted.

Using hog ring pliers, install new hog rings.
Note
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.

INSTALL FRONT SEAT HEADREST SUPPORT
1. Attach the 4 claws to install the 2 front seat headrest supports.
INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System)
1. Attach the 4 hooks to install the seat climate control controller LH.
2. Attach the 2 claws to connect the seat climate control blower LH.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH
1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.
2. Install the 2 screws.
INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)
1. Install the television display assembly with the 3 nuts.
  
  Torque:
  
  5.5 N*m { 56 kgf*cm, 49 in.*lbf }
2. Connect the connector.
INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)
1. Attach the 3 guides and 3 claws to install the television base.
INSTALL FRONT INNER SEAT CUSHION SHIELD LH
1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.
2. Install the screw.
INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
1. Install the front seat inner belt assembly with the nut.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
2. Connect the 3 connectors and attach the clamps.
INSTALL FRONT SEAT CUSHION SHIELD LH
1. Attach the 2 wire harness clamps.
2. Connect the 2 connectors.
3. Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.
4. Install the 3 screws.
5. Connect the connector.
6. Install the 2 screws.
7. Connect the 2 rubber band.
INSTALL FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)
1. Attach the claw to install the front inner No. 1 cushion shield RH to the front seat cushion shield RH.
2. Install the screw.
INSTALL RECLINING POWER SEAT SWITCH KNOB
1. Attach the 2 claws to install the reclining power seat switch knob.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
1. Attach the 2 claws to install the slide and vertical power seat switch knob.
INSTALL FRONT SEAT ASSEMBLY LH

Click here