LUMBAR SUPPORT ADJUSTER ASSEMBLY REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A01EN8KE02
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Using a screwdriver, detach the 2 claws and remove the slide and vertical power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE RECLINING POWER SEAT SWITCH KNOB

    A01EPMYE02
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE FRONT SEAT CUSHION SHIELD LH

    A01ENHA

    1. Remove the 2 screws.

    2. Disconnect the 2 rubber bands.

    3. A01EQ2T

      Disconnect the connector.

    4. A01EPVL

      Remove the 3 screws.

    5. Detach the 2 claws and remove the front seat cushion shield LH together with the front inner No. 1 seat cushion shield LH.

    6. A01EN8S

      Detach the 2 wire harness clamps.

    7. Disconnect the 2 connectors.

  5. REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side)

    A01ES9A

    1. Remove the 2 screws.

    2. Disconnect the 2 rubber bands.

    3. A01EO2Y

      Disconnect the connector.

    4. A01EOZD

      Remove the 3 screws.

    5. Detach the 2 claws and remove the front seat cushion shield RH together with the front inner No. 1 seat cushion shield RH.

    6. A01EOKG

      Disconnect the connector.

  6. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. Disconnect the 3 connectors and detach the clamps.

    2. A01EPCP

      Remove the nut and front seat inner belt assembly.

    3. Remove the front seat belt anchor plate.

  7. REMOVE FRONT INNER SEAT CUSHION SHIELD LH

    A01ERB2

    1. Remove the screw.

    2. Detach the 2 claws and clip, and then remove the front inner seat cushion shield LH.

  8. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. A01EP63E01
      Text in Illustration
      *1 Protective tape

      Put protective tape around the No. 1 instrument panel garnish sub-assembly.

    2. Using a moulding remover A, detach the 3 claws and 3 guides and remove the television base.

  9. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)


    1. A01EOY5

      Disconnect the connector.

    2. Remove the 3 nuts and television display assembly.

  10. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01EQYS

    1. Remove the 2 screws.

    2. Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.

  11. REMOVE SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System)

    A01ENZK

    1. Detach the 2 claws and disconnect the seat climate control blower LH.

    2. Detach the 4 hooks and remove the seat climate control controller LH.

  12. REMOVE FRONT SEAT HEADREST SUPPORT

    A01ERPO

    1. Detach the 4 claws and remove the 2 front seat headrest supports.

  13. REMOVE SEATBACK COVER WITH PAD


    1. A01EQ8FE02
      Text in Illustration
      *1 Hog Ring

      Remove the hog rings.

    2. A01ENFVE01
      Text in Illustration
      *1 Seatback Cover Bracket

      Remove the nut and detach the seatback cover bracket.

    3. Detach the hooks and remove the seatback cover with pad.

  14. REMOVE FRONT SEATBACK PROTECTOR

    A01EPVUE01
    Text in Illustration
    *A w/ Rear Seat Entertainment System
    *1 Double-sided Tape

    1. Remove the front seatback protector.

    2. Remove any remaining double-sided tape.

  15. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH


    1. A01EQ5FE01
      Text in Illustration
      *1 Cable Clamp
      *2 Hook

      Remove the cable clamp and disconnect the active headrest cable from the seatback spring.

    2. Remove the 4 springs.

    3. Detach the 4 hooks and remove the seatback spring.

    4. A01EPSF

      Disconnect the connector.

    5. Remove the 2 screws and lumbar support adjuster assembly LH.