REAR SEATBACK HEATER (for 60/40 Split Seat Type 60 Side) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.


  1. REMOVE REAR NO. 1 SEAT ASSEMBLY


    1. Remove the rear No. 1 seat assembly Click here.

  2. REMOVE SEAT ADJUSTER BOLT COVER

    A01ERJV

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    A01EQQW

    1. Remove the screw and release handle.

  4. REMOVE REAR NO. 1 SEAT RECLINING COVER LH

    A01EO18E01

    1. Remove the 2 screws.

    2. Detach the 3 claws in the order shown in the illustration, and then remove the cover.

  5. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

    A01ESFT

    1. Remove the 2 screws.

    2. Detach the 4 claws and remove the cover.

  6. REMOVE UPPER SEAT TRACK RAIL COVER LH

    A01EPQA

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  7. REMOVE UPPER SEAT TRACK RAIL COVER RH

    A01ES1O

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  8. REMOVE REAR NO. 2 SEAT LEG SIDE COVER


    1. A01EP94

      Remove the 4 screws and detach the 4 claws.

    2. A01ERC0

      Remove the bolt that is securing the fold seat stopper band and remove the seat leg side cover together with the fold seat stopper band.

  9. REMOVE REAR NO. 2 SEAT PROTECTOR


    1. A01ESK0

      Detach the claw and remove the wire harness connector.

    2. w/ Seat Heater System:

      Detach the claw and remove the wire harness connector.

    3. A01ES77

      Using a clip remover, remove the clip.

    4. Detach the claw and remove the seat protector from the seat hinge.

    5. Detach the 2 claws, open the protector and remove the wire harness.

  10. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A01EOCH

      Detach the wire harness clamp.

    2. w/ Seat Heater System:

      Detach the wire harness clamp.

    3. Remove the 2 nuts and hinge.

  11. REMOVE REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH

    A01EOO8

    1. Remove the 2 nuts and hinge.

  12. REMOVE SEAT BELT ANCHOR COVER CAP


    1. A01EOL9

      Detach the claw and open the cap.

    2. A01ER1C

      Remove the screw and anchor cover cap.

  13. REMOVE REAR SEATBACK STAY COVER LH

    A01EOZA

    1. Remove the screw.

    2. Detach the 2 claws and remove the cover.

  14. REMOVE REAR UNDER SIDE COVER LH


    1. A01EQDR

      Detach the 10 claws.

    2. A01ERPJ

      Remove the 5 screws.

    3. Detach the 2 clips and 2 claws, and remove the cover.

  15. REMOVE REAR SEAT CUSHION COVER RH

    A01ERSG

    1. Remove the 4 screws.

    2. Detach the 2 claws and remove the cover.

  16. REMOVE REAR SEAT UNDER TRAY COVER LH

    A01EO07

    1. Remove the 2 screws and cover.

  17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    A01EOH9E01

    1. Remove the bolt and belt.

      Tech Tips

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, it becomes disconnected when the bolt is removed.

  18. DISCONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A01EN0JE02

    1. Disconnect the belt anchor.

  19. REMOVE SEAT CUSHION COVER WITH PAD


    1. Detach the side airbag wire harness clamps.

    2. Remove the side airbag wire harness through the hole in the seat cushion.

    3. w/ Seat Heater System:


      1. A01ER2U

        Disconnect the 2 seat heater connectors.

      2. A01ESGY

        Remove the seatback heater wire harness through the hole in the seat cushion.

    4. Remove the seat cushion cover with pad.

  20. REMOVE REAR SEATBACK COVER

    A01EOQAE01

    1. Using a screwdriver, detach the 4 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  21. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH

    A01ES1P

    1. Detach the 2 claws on the top of the board.

    2. Pull up the board to detach the 2 claws on the bottom of the board and remove it.

  22. REMOVE REAR SEAT HEADREST ASSEMBLY

  23. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    A01ER3J

    1. Detach the 4 claws and remove the 2 supports.

  24. REMOVE SHOULDER BELT ANCHOR COVER

    A01EQZWE01

    1. Using a screwdriver, detach the 2 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  25. REMOVE REAR SEAT BELT HOLE COVER LH

    A01ES97

    1. Remove the 2 screws.

    2. Detach the 4 claws and remove the cover.

  26. REMOVE SEATBACK COVER WITH PAD


    1. A01EP9I

      Remove the hog rings.

    2. A01ES89

      Remove the cap nut and seatback cover bracket from the seat frame.

    3. Remove the side airbag wire harness through the hole in the seatback.

    4. w/ Seat Heater System:


      1. A01EPVHE01

        Cut the cable tie and disconnect the seatback heater wire harness.

      2. A01ENKF

        Remove the seatback heater wire harness through the hole in the seatback.

    5. A01EQUS

      Pull the seat belt into the inside of the seat.

    6. Remove the seatback cover with pad.

  27. REMOVE REAR SEPARATE TYPE SEATBACK COVER


    1. A01EPR9

      Disconnect the seatback cover bracket from the seatback pad.

    2. Remove the hog rings and rear seatback cover.

  28. REMOVE REAR SEATBACK HEATER ASSEMBLY


    1. A01EPSO

      Set the rear seatback heater assembly with the name stamp side facing the seatback cover.

    2. Install the rear seatback heater assembly with new tack pins.