REAR NO. 2 SEAT ASSEMBLY (w/ Automatic Folding-up Function) REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.


  1. INSTALL NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY

    A01ENM6

    1. Install the release handle with the bolt.

  2. INSTALL REAR SEATBACK LOCK STRIKER COVER LH


    1. Attach the 2 clamps to install the cover.

  3. INSTALL REAR NO. 2 SEATBACK COVER LH


    1. Attach the 3 claws to install the cover.

  4. INSTALL REAR SEATBACK LOCK STRIKER ASSEMBLY LH

    A01ENFE

    1. Install the lock striker with the 2 nuts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

  5. INSTALL REAR NO. 2 SEAT WIRE LH

    A01EQRW

    1. Connect the 5 connectors and attach the 4 clamps to install the rear No. 2 seat wire LH.

  6. INSTALL REAR SEAT LOCK CONTROL CABLE

    A01EOM4

    1. Attach the 2 clamps to install the lock control cable.

    2. Attach the cable clamp to connect the cable.

  7. INSTALL REAR INNER SEAT RECLINING COVER LH

    A01ENZ6

    1. Attach the claw to install the cover.

    2. Install the screw.

  8. INSTALL REAR INNER SEAT RECLINING COVER RH


    1. Attach the claw to install the cover.

    2. Install the screw.

  9. INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH

    A01ER6VE01

    1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  10. INSTALL REAR SEAT HEADREST HANDLE


    1. Install the snap ring to the headrest handle.

    2. A01ENLP

      Install the headrest handle to the headrest.

  11. INSTALL SEATBACK COVER WITH PAD


    1. A01EPAZ

      Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog ring.

    2. for LH Side:


      1. A01ERH4

        Attach the 8 claws to install the 4 headrest supports.

      2. Install the rear seat protector.

    3. for RH Side:


      1. A01EPMQ

        Attach the 4 claws to install the 2 headrest supports.

    4. A01EQBDE02

      While releasing the lock inside the headrest support with a screwdriver, install the headrest.

      Tech Tips

      Tape the screwdriver tip before use.

    5. A01EON5

      Attach the clamp.

    6. Attach the cable clamp to connect the cable.

    7. A01EN66

      Install the seat protector.

    8. A01EOFZ

      Insert the center headrest storage bag.

    9. A01EOE4

      Attach the 2 hooks.

    10. A01EOEY

      Close the fastener.

  12. INSTALL REAR SEAT HINGE PAWL GUIDE

    A01EPKX

    1. Install the guide with the 3 screws.

  13. INSTALL REAR SEAT HINGE PAWL GUIDE

    A01ERLS

    1. Attach the 5 claws to install the guide.

  14. INSTALL REAR LOWER SEATBACK LOCK BEZEL

    A01ESAZ

    1. Attach the 3 claws and clip to install the seatback lock bezel.

  15. INSTALL REAR NO. 2 SEATBACK CUSHION

    A01EQVE

    1. Install the seatback cushion with the screw.

  16. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH

    A01ES5B

    1. Install the lever with the 2 bolts.

  17. INSTALL NO. 3 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY


    1. A01EP2G

      Attach the 2 cable clamps to connect the 2 cables.

    2. A01EPLO

      Attach the 2 clamps and then install the 2 cables with the 2 bolts.

  18. INSTALL NO. 2 SEAT STAY SUB-ASSEMBLY

    A01EPG8

    1. Install the seat stay with the bolt.

  19. INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH

    A01EODDE01

    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A01ERKU

      Attach the 4 clamps.

    3. Connect the 3 connectors.

    4. Install 2 new cable ties.

    5. A01EQQF

      Install the E-ring and attach the clamp.

    6. Attach the cable clamp and connect the cable.

  20. INSTALL NO. 3 SEAT CUSHION PAD LH

  21. INSTALL SEAT CUSHION COVER WITH PAD

  22. INSTALL REAR SEAT CUSHION CARPET

    A01EMU3

    1. Install the seat cushion carpet with new tack pins.

  23. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY


    1. Install the 2 belts.

      A01EOM1E01

      Note


      • Make sure the claws are facing away from the seat.

      • Do not overlap the anchor part of the seat belt and protruding parts of the seat.

  24. INSTALL REAR SEAT OUTER BELT SUB-ASSEMBLY (for RH Side)

    A01EOLWE01

    1. Install the belt with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the seat.

      Tech Tips

      The rear No. 2 seat inner belt is fixed with the same nut as the rear seat outer belt. Therefore, connect it when installing the rear seat outer belt.

  25. INSTALL REAR SEAT INNER BELT SUB-ASSEMBLY (for LH Side)

    A01ER0LE01

    1. Install the belt with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not overlap the anchor part of the seat belt and protruding parts of the seat.

      Tech Tips

      The rear No. 2 seat inner belt is fixed with the same nut as the rear seat inner belt. Therefore, connect it when installing the rear seat inner belt.

  26. INSTALL REAR SEAT LOCK COVER LH

    A01ENYR

    1. Attach the 2 clamps to install the 2 covers.

    2. Install the 2 screws.

  27. INSTALL NO. 3 SEAT LEG COVER NO. 2

    A01EPH8

    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  28. INSTALL NO. 3 SEAT FRONT BRACKET COVER LH

    A01ENP9

    1. Attach the 4 claws to install the cover.

  29. INSTALL REAR SEAT CUSHION UNDER COVER LH


    1. A01EPKJ

      Install the cover with the 7 screws.

    2. A01EQ0R

      Attach the 16 claws.

  30. INSTALL 3RD SEAT CUSHION LOCK COVER

    A01EQ3A

    1. Attach the 4 claws to install the 2 covers.

  31. INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH

    A01EQKO

    1. Install the seat link with the bolt and nut.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

  32. INSTALL REAR SEAT INNER RECLINING COVER LH

    A01EQN1

    1. Attach the 2 claws to install the cover.

  33. INSTALL RECLINING ADJUSTER COVER RH

    A01EOYVE02

    1. Attach the 5 claws in the order shown in the illustration to install the cover.

    2. Install the screw.

  34. INSTALL RECLINING ADJUSTER COVER LH

    A01EMXNE02

    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the screw.

  35. INSTALL NO. 2 SEAT LEG COVER NO. 2

    A01ENK6

    1. Install the seat leg cover with the screw.

  36. INSTALL REAR NO. 3 SEAT LEG COVER LH


    1. A01EPV2

      Attach the 2 claws to install the seat leg cover.

    2. Install the 2 screws.

    3. A01EN71

      Install the spring of the seat stay ball joint.

    4. Connect the seat stay to the seat frame.

  37. INSTALL REAR SEAT REAR BRACKET COVER REAR


    1. Attach the 2 claws to install the cover.

  38. INSTALL NO. 2 RECLINING ADJUSTER RELEASE HANDLE LH

    A01EOHP

    1. Install the release handle with the screw.

  39. INSTALL SEAT ADJUSTER BOLT COVER

    A01EQJ1

    1. Attach the 2 claws to install the cover.

  40. INSTALL REAR NO. 2 SEAT LEG BRACKET REAR LH

    A01EN4D

    1. Install the bracket with the bolt and nut.

    2. A01EQ32

      Attach the 4 clamps.

  41. INSTALL FOLD SEAT CONTROL ECU

    A01EOI9

    1. Attach the 2 claws to install the ECU.

    2. Connect the 2 connectors.

  42. INSTALL NO. 2 SEAT CUSHION COVER

    A01EPVC

    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  43. INSTALL POWER SEAT MOTOR SUB-ASSEMBLY

    A01ES1I

    1. Using a 5 mm hexagon socket wrench, install the motor with the 4 bolts.

    2. Connect the 2 connectors.