REAR NO. 2 SEAT ASSEMBLY (w/ Automatic Folding-up Function) REMOVAL

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.


  1. REMOVE REAR NO. 2 SEAT HEADREST ASSEMBLY LH

  2. REMOVE REAR SEAT CUSHION HINGE COVER LH

    A01EMW4

    1. Apply protective tape to the rear seatback lock striker as shown in the illustration to prevent the seat from locking.

    2. Operate the power seat switch and move the seat to the storage position.

      Tech Tips

      Make sure that the lock and striker are not engaged.

    3. A01EN36

      Using a screwdriver, detach the 3 claws and remove the cover.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE REAR NO. 2 SEAT HINGE COVER LH

    A01EN8L

    1. Detach the 3 claws and 2 clips, and then remove the cover.

  4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. REMOVE REAR NO. 2 SEAT ASSEMBLY

    A01EO0X

    1. Disconnect the connector.

    2. Remove the 4 bolts and seat assembly.

      Note

      Be careful not to damage the vehicle body.

  6. REMOVE REAR STEP COVER

    Tech Tips

    Use the same procedure to remove the step cover on the other side.


    1. A01EQ9D

      w/o Illumination Type Front Door Scuff Plate:

      Detach the 2 claws and remove the step cover.

    2. A01EQ94

      w/ Illumination Type Front Door Scuff Plate:

      Detach the 4 claws and remove the step cover.

  7. REMOVE REAR DOOR SCUFF PLATE LH

    A01EN6Q

    1. w/o Illumination Type Front Door Scuff Plate:

      Remove the rear door scuff plate.


      1. Remove the screw.

      2. Detach the 3 claws and 4 clips, and remove the scuff plate.

    2. A01ERAD

      w/ Illumination Type Front Door Scuff Plate:

      Remove the rear door scuff plate.


      1. Remove the screw.

      2. Detach the 3 claws and 4 clips, and remove the scuff plate.

  8. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    A01EQA6

    1. Detach the 6 clips and 4 claws, and remove the support plate.

  9. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    A01ERFB

    Tech Tips

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. A01ESN6

      Detach the 3 claws and remove the cover.

    2. A01EOE1

      Remove the bolt and rear No. 1 seat belt anchor.

    3. A01EQO3

      Remove the bolt and rear No. 2 seat belt anchor.

    4. Remove the clip.

    5. Detach the 19 clips and 2 claws.

    6. Disconnect the thermistor connector and then remove the quarter trim panel.

      A01ENWJ

  10. REMOVE REAR ROOF NO. 1 AIR DUCT (for LH Side)

    A01ENOM

    1. Detach the 2 claws and remove the cooler plate.

    2. A01EO6Q

      Remove the clip and duct.

  11. REMOVE NO. 1 WOOFER BOX SPEAKER ASSEMBLY (for RH Side, w/ Woofer)


    1. Disconnect the connector.

    2. A01ENTM

      Remove the 5 bolts and box speaker.

  12. REMOVE FOLD SEAT LEG LOCK SUB-ASSEMBLY


    1. A01ENXF

      Disconnect the connector.

    2. Detach the 2 cable clamps.

    3. A01ENZH

      Remove the 2 nuts and fold seat leg lock.

  13. REMOVE NO. 3 SEAT CUSHION COVER


    1. A01EPZG

      Detach the 4 clips and 16 claws, and remove the 4 seat cushion covers.

  14. REMOVE REAR SEAT LOCK STRIKER SUB-ASSEMBLY


    1. Fold back the floor carpet.

    2. A01ERNQ

      Remove the 8 bolts and 4 seat lock strikers.

  15. REMOVE FOLD SEAT SWITCH ASSEMBLY

    A01ENO7

    1. Detach the 6 clips.

    2. Disconnect the connector and then remove the fold seat switch.

    3. A01EQC7E01

      Detach the claw and remove the light.