FRONT SEAT SIDE AIRBAG ASSEMBLY INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedures for LHD and RHD vehicles.

  • The procedures listed below are for LHD vehicles.


  1. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    CAUTION:

    Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.


    1. A01ENZZ

      Install the front seat airbag assembly with 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    2. Attach the 2 clamps to connect the wire harness.

    3. A01EQS5

      w/o Climate Control Seat System


      1. Attach the 5 clamps to connect the wire harness.

    4. A01ES2Y

      w/ Climate Control Seat System


      1. Attach the 4 clamps and disconnect the wire harness.

  2. INSTALL SEATBACK COVER WITH PAD

    A01EO2KE01
    Text in Illustration
    *1 Hog Ring
    *2 Hog Ring Pliers

    1. Attach the hooks to install the seatback cover with pad.

    2. A01ENFVE02
      Text in Illustration
      *1 Seatback Cover Bracket
      *2 Side Airbag Strap

      Attach the seatback cover bracket with the nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      CAUTION:

      After the front separate type seatback cover is assembled, make sure the side airbag strap is not twisted.

    3. Using hog ring pliers, install new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

  3. INSTALL FRONT SEAT HEADREST SUPPORT

    A01EMZF

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  4. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH

    A01ESA2

    1. Move the front seatback board sub-assembly in the direction of the arrow to attach the 2 hooks and install it.

    2. Install the 2 screws.

  5. INSTALL FRONT INNER SEAT CUSHION SHIELD LH

    A01ERB2

    1. Attach the 2 claws and clip to install the front inner seat cushion shield LH.

    2. Install the screw.

  6. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. Install the front seat belt anchor plate.

    2. A01ENHVE01

      Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    3. Connect the 3 connectors and attach the clamps.

  7. INSTALL FRONT SEAT CUSHION SHIELD LH

    A01EN8S

    1. Attach the 2 wire harness clamps.

    2. Connect the 2 connectors.

    3. A01EPVL

      Attach the 2 claws to install the front seat cushion shield LH together with the front inner No. 1 cushion shield LH.

    4. Install the 3 screws.

    5. A01EQ2T

      Connect the connector.

    6. A01ENHA

      Install the 2 screws.

    7. Connect the 2 rubber band.

  8. INSTALL RECLINING POWER SEAT SWITCH KNOB

    A01EOXD

    1. Attach the 2 claws to install the reclining power seat switch knob.

  9. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

    A01EQ7J

    1. Attach the 2 claws to install the slide and vertical power seat switch knob.

  10. INSTALL FRONT SEAT ASSEMBLY LH


    1. Install the front seat assembly LH Click here.