AIRBAG SYSTEM, Diagnostic DTC:B1676/85, B1677/85

DTC Code DTC Name
B1676/85 Lost Communication with Rear Floor Airbag Sensor RH
B1677/85 Rear Floor Airbag Sensor RH Initialization Incomplete

DESCRIPTION

Tech Tips

"Rear floor airbag sensor RH" refers to the rear floor airbag sensor.


DTC Code DTC Detection Condition Trouble Area
B1676/85

When one of the following conditions is met:


  • The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear floor airbag sensor circuit for 2 seconds.

  • A rear floor airbag sensor malfunction.

  • A center airbag sensor malfunction.

  • No. 2 floor wire

  • Rear floor airbag sensor

  • Center airbag sensor assembly
B1677/85

When one of the following conditions is met:


  • The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the rear floor airbag sensor circuit for 2 seconds.

  • A rear floor airbag sensor malfunction.

  • A center airbag sensor malfunction.

  • No. 2 floor wire

  • Rear floor airbag sensor

  • Center airbag sensor assembly

WIRING DIAGRAM

A01ENNKE36

INSPECTION PROCEDURE

Note


  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

PROCEDURE


  1. CHECK CONNECTION OF CONNECTORS


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor and the rear floor airbag sensor.

      OK
      The connectors are properly connected.

    NG

    CONNECT CONNECTORS PROPERLY

    OK

  2. CHECK CONNECTORS


    1. Disconnect the connectors from the center airbag sensor and rear floor airbag sensor.

    2. Check that the connectors (on the center airbag sensor side and rear floor airbag sensor side) are not damaged.

      OK
      The connectors are not deformed or damaged.

    NG

    REPLACE HARNESS AND CONNECTOR

    OK

  3. CHECK REAR FLOOR AIRBAG SENSOR CIRCUIT

    A01ESLTE01

    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L19-2 (BER+) - Body ground Engine switch on (IG) Below 1 V
      L19-1 (BER-) - Body ground Engine switch on (IG) Below 1 V

    3. Turn the engine switch off.

    4. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    5. Using a service wire, connect terminals 21 (BDR+) and 22 (BDR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L19-2 (BER+) - L19-1 (BER-) Always Below 1 Ω

    7. Disconnect the service wire from connector B.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L19-2 (BER+) - L19-1 (BER-) Always 1 MΩ or higher
      L19-2 (BER+) - Body ground Always 1 MΩ or higher
      L19-1 (BER-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  4. CHECK REAR FLOOR AIRBAG SENSOR

    A01EQG0E02

    1. Connect the connectors to the center airbag sensor.

    2. Temporarily replace the rear floor airbag sensor with a new one.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the engine switch on (IG), and wait for at least 60 seconds.

    5. Clear the DTCs stored in the memory Click here.

    6. Turn the engine switch off.

    7. Turn the engine switch on (IG), and wait for at least 60 seconds.


      1. Check for DTCs Click here.

        OK
        DTC B1676 and B1677 are not output.

        Tech Tips

        Codes other than DTC B1676 and B1677 may be output at this time, but they are not related to this check.


    A

    USE SIMULATION METHOD TO CHECK Click here

    B

    REPLACE REAR FLOOR AIRBAG SENSOR Click here

    C

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here