AIRBAG SYSTEM, Diagnostic DTC:B1925/78, B1926/78, B1927/78, B1928/78

DTC Code DTC Name
B1925/78 Short in Rear Pretensioner Squib LH Circuit
B1926/78 Open in Rear Pretensioner Squib LH Circuit
B1927/78 Short to GND in Rear Pretensioner Squib LH Circuit
B1928/78 Short to B+ in Rear Pretensioner Squib LH Circuit

DESCRIPTION

The rear pretensioner squib LH circuit consists of the center airbag sensor and the rear seat outer belt LH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear pretensioner squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1925/78

When one of the following conditions is met:


  • The center airbag sensor receives a line short circuit signal 5 times in the rear pretensioner squib LH circuit during the primary check.

  • A rear pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • Floor wire

  • Rear seat outer belt assembly LH (Rear pretensioner squib LH)

  • Center airbag sensor assembly
B1926/78

When one of the following conditions is met:


  • The center airbag sensor receives an open circuit signal in the rear pretensioner squib LH circuit for 2 seconds.

  • A rear pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • Floor wire

  • Rear seat outer belt assembly LH (Rear pretensioner squib LH)

  • Center airbag sensor assembly
B1927/78

When one of the following conditions is met:


  • The center airbag sensor receives a short circuit to ground signal in the rear pretensioner squib LH circuit for 0.5 seconds.

  • A rear pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • Floor wire

  • Rear seat outer belt assembly LH (Rear pretensioner squib LH)

  • Center airbag sensor assembly
B1928/78

When one of the following conditions is met:


  • The center airbag sensor receives a short circuit to B+ signal in the rear pretensioner squib LH circuit for 0.5 seconds.

  • A rear pretensioner squib LH malfunction.

  • A center airbag sensor malfunction.

  • Floor wire

  • Rear seat outer belt assembly LH (rear pretensioner squib LH)

  • Center airbag sensor assembly

WIRING DIAGRAM

A01ENTRE12

INSPECTION PROCEDURE

Note


  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

Tech Tips

To perform the simulation method, enter the check mode (signal check) with the intelligent tester Click here, and then wiggle each connector of the airbag system or drive the vehicle on various type of road Click here.

PROCEDURE


  1. CHECK REAR SEAT OUTER BELT LH (REAR PRETENSIONER SQUIB LH)

    A01ESEUE05

    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the connectors from the rear seat outer belt LH.

    4. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the rear seat outer belt LH (rear pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Clear the DTCs Click here.

    8. Turn the engine switch off.

    9. Turn the engine switch on (IG), and wait for at least 60 seconds.

    10. Check for DTCs Click here.

      OK
      DTC B1925, B1926, B1927 or B1928 is not output.

      Tech Tips

      Codes other than DTC B1925, B1926, B1927 and B1928 may be output at this time, but they are not related to this check.


    NG

    CHECK CONNECTOR Click here

    OK

    REPLACE REAR SEAT OUTER BELT ASSEMBLY LH Click here

  2. CHECK CONNECTOR


    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect SST from connector C.

    4. Check that the floor wire connector (on the rear seat outer belt LH side) is not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not damaged or deformed.

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK FLOOR WIRE (REAR PRETENSIONER SQUIB LH CIRCUIT)

    A01EPD6E05

    1. Disconnect the connectors from the center airbag sensor.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K13-1 (RL+) - Body ground Engine switch on (IG) Below 1 V
      K13-2 (RL-) - Body ground Engine switch on (IG) Below 1 V

    4. Turn the engine switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K13-1 (RL+) - K13-2 (RL-) Always Below 1 Ω

    7. Release the activation prevention mechanism built into connector B Click here.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K13-1 (RL+) - K13-2 (RL-) Always 1 MΩ or higher
      K13-1 (RL+) - Body ground Always 1 MΩ or higher
      K13-2 (RL-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK CENTER AIRBAG SENSOR

    A01ENOBE01

    1. Connect the connectors to the rear seat outer belt LH and the center airbag sensor.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the engine switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs Click here.

    5. Turn the engine switch off.

    6. Turn the engine switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1925, B1926, B1927 or B1928 is not output.

      Tech Tips

      Codes other than DTC B1925, B1926, B1927 or B1928 may be output at this time, but they are not related to this check.


    NG

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here