DOOR CONTROL RECEIVER INSTALLATION


  1. INSTALL DOOR CONTROL RECEIVER


    1. A01ESI5

      Install the receiver with the bolt.

      Torque:
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

    2. Connect the connector.

  2. INSTALL REAR UPPER PILLAR GARNISH RH

    A01EOVD

    1. w/o Power Back Door:


      1. Attach the 5 clips to install the rear upper pillar garnish.

    2. A01EON9E01

      w/ Power Back Door:


      1. Pass the power back door rod through the rear upper pillar garnish.

      2. Attach the 5 clips to install the rear upper pillar garnish.

    3. A01EOVO

      Install the seat belt shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    4. A01EP2O

      Attach the 2 claws to close the seat belt shoulder anchor cover.

  3. INSTALL BACK DOOR SERVICE HOLE COVER RH (w/ Power Back Door)


    1. When reusing the power back door rod:


      1. A01ENFF

        Install the back door stay plate.

      2. A01ENC5E02

        Pass the power back door rod through the hole of the back door service hole cover and install the rod with the bolt.

        Torque:
        18 N*m  { 184 kgf*cm, 13 ft.*lbf }
      3. A01ENSXE01
        Text in Illustration
        *1 Power Back Door Rod
        *2 Hole of Back Door Service Hole Cover
        *a Back Door is Half-open

        Move the back door to a half-open position so that the hole in the center of the back door service hole cover is aligned lengthwise with the power back door rod.

      4. A01EPNA

        Attach the 2 clips and install the back door service hole cover.

        Note

        If the back door is in a fully-open position, the power back door rod will interfere with the hole of the back door service hole cover, so do not perform this operation with the back door in a fully open position.

    2. When installing a new power back door rod:


      1. A01ENFF

        Install the back door stay plate.

      2. A01EQI4

        Install the back door stay bolt.

        Torque:
        18 N*m  { 184 kgf*cm, 13 ft.*lbf }
      3. A01ESOW

        Attach the 2 clips to install the service hole cover.

      4. A01EOUD

        Attach the ball joints to install the power back door rod.

  4. INSTALL BACK DOOR SIDE GARNISH RH


    1. w/o Power Back Door:

      Tech Tips

      Use the same procedures described for the LH side.

    2. w/ Power Back Door:


      1. A01EPSU

        Attach the clip and 2 claws to install the back door side garnish.

  5. INSTALL CENTER BACK DOOR GARNISH


    1. A01ERXU

      Attach the 5 clips and 2 claws to install the back door garnish.

  6. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    A01ENK2

    Tech Tips

    When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. Connect the thermistor connector.

    2. Attach the 17 clips and 2 claws to install the quarter trim panel.

    3. Install the clip.

      A01EREO
    4. A01EQD8

      Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    5. A01ES5O

      Attach the 3 claws to install the cover.

    6. A01EPT5

      Install the rear No. 1 seat belt anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    7. A01EOL1

      Attach the 3 claws to install the cover.

  7. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

    A01EQA6

    1. Attach the 6 clips and 4 claws to install the support plate.

  8. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedures described for the LH side.

  9. INSTALL REAR STEP COVER

    Tech Tips

    Use the same procedure to install the step cover on the other side.


    1. A01EQ9D

      w/o Illumination Type Front Door Scuff Plate:

      Attach the 2 claws to install the step cover.

    2. A01EQ94

      w/ Illumination Type Front Door Scuff Plate:

      Attach the 4 claws to install the step cover.

  10. INSTALL REAR NO. 2 SEAT ASSEMBLY RH


    1. Install the rear No. 2 seat assembly RH Click here.