CAN COMMUNICATION SYSTEM (for RHD), Diagnostic DTC:U1002 (CAN MS BUS)

DESCRIPTION

• The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.

• When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.

• If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. PRECAUTION

   Note

   After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

   
   

   NEXT

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

   
   

   1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

   
   

   NEXT

3. CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT)

   
   
   1. 

      Text in Illustration

      *1	Component with harness connected (Main Body ECU [Cowl Side Junction Block LH])
      *2	DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Switch Condition Specified Condition Resistance Malfunction E3-16 (CANP) - E3-15 (CANN) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line E3-16 (CANP) - E3-15 (CANN) Engine switch off 54 to 69 Ω 70 Ω or higher: Open in CAN main bus line E3-16 (CANP) - E22-16 (BAT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short E3-15 (CANN) - E22-16 (BAT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short E3-16 (CANP) - E22-4 (CG) Engine switch off 200 Ω or higher Below 200 Ω: Ground short E3-15 (CANN) - E22-4 (CG) Engine switch off 200 Ω or higher Below 200 Ω: Ground short

      Result

      Result	Proceed to
      NG Open in CAN main wire	A
      NG Short in line +B short Ground short	B
      OK	C

   
   

   B

   CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE) Click here

   C

   CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND) Click here

   A

4. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

   
   
   1. 

      Text in Illustration

      *1	Rear view of wire harness connector (to No. 2 CAN Junction Connector)

      Disconnect the L29 No. 2 CAN junction connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition L29-1 (CANH) - L29-2 (CANL) Engine switch off 108 to 132 Ω

   
   

   NG

   CONNECT CONNECTOR Click here

   OK

5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

   
   
   1. 

      Text in Illustration

      *1	Rear view of wire harness connector (to No. 2 CAN Junction Connector)

      Disconnect the L30 No. 2 CAN junction connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition L30-1 (CANH) - L30-2 (CANL) Engine switch off 108 to 132 Ω

   
   

   NG

   CONNECT CONNECTOR Click here

   OK

   REPLACE NO. 2 CAN JUNCTION CONNECTOR

6. CONNECT CONNECTOR

   
   

   1. Reconnect the L29 No. 2 CAN junction connector.

   
   

   NEXT

7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

   
   
   1. 

      Text in Illustration

      *1	Rear view of wire harness connector (to No. 8 Junction Connector)

      Disconnect the E73 No. 8 junction connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition E73-3 (CANH) - E73-14 (CANL) Engine switch off 108 to 132 Ω

   
   

   NG

   CONNECT CONNECTOR Click here

   OK

8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

   
   
   1. 

      Text in Illustration

      *1	Rear view of wire harness connector (to No. 8 Junction Connector)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition E73-1 (CANH) - E73-12 (CANL) Engine switch off 108 to 132 Ω

   
   

   NG

   REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

   OK

   REPLACE NO. 8 JUNCTION CONNECTOR

9. CONNECT CONNECTOR

   
   

   1. Reconnect the E73 No. 8 junction connector.

   
   

   NEXT

10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to Main Body ECU [Cowl Side Junction Block LH])

       Disconnect the E3 main body ECU (cowl side junction block LH) connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E3-16 (CANP) - E3-15 (CANN) Engine switch off 108 to 132 Ω

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)

    OK

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

11. CONNECT CONNECTOR

    
    

    1. Reconnect the L29 and L30 No. 2 CAN junction connectors.

    
    

    NEXT

12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 10 Junction Connector)

       Disconnect the E70 No. 10 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E70-1 (CANH) - E70-12 (CANL) Engine switch off 108 to 132 Ω

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 10 Junction Connector)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E70-3 (CANH) - E70-14 (CANL) Engine switch off 108 to 132 Ω

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 10 JUNCTION CONNECTOR

14. CONNECT CONNECTOR

    
    

    1. Reconnect the E70 No. 10 junction connector.

    
    

    NEXT

15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Front view of wire harness connector (to Combination Meter Assembly)

       Disconnect the E77 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E77-37 (MPX+) - E77-38 (MPX-) Engine switch off 108 to 132 Ω

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR)

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

16. CONNECT CONNECTOR

    
    

    1. Reconnect the E70 No. 10 junction connector.

    
    

    NEXT

17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 9 Junction Connector)

       Disconnect the E76 No. 9 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E76-1 (CANH) - E76-12 (CANL) Engine switch off 108 to 132 Ω

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

    OK

18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 9 Junction Connector)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E76-7 (CANH) - E76-18 (CANL) Engine switch off 108 to 132 Ω

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

    OK

    REPLACE NO. 9 JUNCTION CONNECTOR

19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE)

    
    
    1. 

       Text in Illustration

       *1	Component with harness connected (Main Body ECU [Cowl Side Junction Block LH])
       *2	DLC3

       Disconnect the E70 No. 10 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E3-16 (CANP) - E3-15 (CANN) Engine switch off 108 to 132 Ω E3-16 (CANP) - E22-4 (CG) Engine switch off 200 Ω or higher E3-15 (CANN) - E22-4 (CG) Engine switch off 200 Ω or higher E3-16 (CANP) - E22-16 (BAT) Engine switch off 6 kΩ or higher E3-15 (CANN) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 10 Junction Connector)
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E70-3 (CANH) - E70-14 (CANN) Engine switch off 108 to 132 Ω E70-3 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E70-14 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E70-3 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E70-14 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 10 JUNCTION CONNECTOR

21. CONNECT CONNECTOR

    
    

    1. Reconnect the E70 No. 10 junction connector.

    
    

    NEXT

22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 9 Junction Connector)
       *2	DLC3

       Disconnect the E76 No. 9 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E76-1 (CANH) - E76-12 (CANL) Engine switch off 108 to 132 Ω E76-1 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E76-12 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E76-1 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E76-12 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

    OK

23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE)

    
    
    1. 

       Text in Illustration

       *1	Component with harness connected (Main Body ECU [Cowl Side Junction Block LH])
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E3-16 (CANP) - E3-15 (CANN) Engine switch off 108 to 132 Ω E3-16 (CANP) - E22-4 (CG) Engine switch off 200 Ω or higher E3-15 (CANN) - E22-4 (CG) Engine switch off 200 Ω or higher E3-16 (CANP) - E22-16 (BAT) Engine switch off 6 kΩ or higher E3-15 (CANN) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - POSITION CONTROL ECU AND SWITCH)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 9 Junction Connector)
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E76-4 (CANH) - E76-15 (CANL) Engine switch off 200 Ω or higher E76-4 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E76-15 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E76-4 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E76-15 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 9 Junction Connector)
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E76-3 (CANH) - E76-14 (CANL) Engine switch off 200 Ω or higher E76-3 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E76-14 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E76-3 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E76-14 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 9 Junction Connector)
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E76-5 (CANH) - E76-16 (CANL) Engine switch off 200 Ω or higher E76-5 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E76-16 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E76-5 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E76-16 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - CERTIFICATION ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 9 Junction Connector)
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E76-2 (CANH) - E76-13 (CANL) Engine switch off 200 Ω or higher E76-2 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E76-13 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E76-2 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E76-13 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 9 JUNCTION CONNECTOR

28. CONNECT CONNECTOR

    
    

    1. Reconnect the E76 No. 9 junction connector.

    
    

    NEXT

29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 2 CAN Junction Connector)
       *2	DLC3

       Disconnect the L30 No. 2 CAN junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition L30-1 (CANH) - L30-2 (CANL) Engine switch off 108 to 132 Ω L30-1 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher L30-2 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher L30-1 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher L30-2 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

    OK

30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)

    
    
    1. 

       Text in Illustration

       *1	Component with harness connected (Main Body ECU [Cowl Side Junction Block LH])
       *2	DLC3

       Disconnect the L29 No. 2 CAN junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E3-16 (CANP) - E3-15 (CANN) Engine switch off 108 to 132 Ω E3-16 (CANP) - E22-4 (CG) Engine switch off 200 Ω or higher E3-15 (CANN) - E22-4 (CG) Engine switch off 200 Ω or higher E3-16 (CANP) - E22-16 (BAT) Engine switch off 6 kΩ or higher E3-15 (CANN) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - POWER BACK DOOR ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 2 CAN Junction Connector)
       *2	DLC3

       Disconnect the L45 No. 2 CAN junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition L45-1 (CANH) - L45-2 (CANL) Engine switch off 200 Ω or higher L45-1 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher L45-2 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher L45-1 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher L45-2 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

32. CHECK FOR FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 2 MAIN BODY ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 2 CAN Junction Connector)
       *2	DLC3

       Disconnect the L46 No. 2 CAN junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition L46-1 (CANH) - L46-2 (CANL) Engine switch off 200 Ω or higher L46-1 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher L46-2 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher L46-1 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher L46-2 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 2 CAN JUNCTION CONNECTOR

33. CONNECT CONNECTOR

    
    

    1. Reconnect the L29 and L30 No. 2 CAN junction connectors.

    
    

    NEXT

34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 8 Junction Connector)
       *2	DLC3

       Disconnect the E73 No. 8 junction connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E73-1 (CANH) - E73-12 (CANL) Engine switch off 108 to 132 Ω E73-1 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E73-12 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E73-1 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E73-12 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

    OK

35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - WINDSHIELD WIPER ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 8 Junction Connector)
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E73-4 (CANH) - E73-15 (CANL) Engine switch off 200 Ω or higher E73-4 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E73-15 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E73-4 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E73-15 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 8 Junction Connector)
       *2	DLC3

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E73-3 (CANH) - E73-14 (CANL) Engine switch off 108 to 132 Ω E73-3 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E73-14 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E73-3 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E73-14 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    CONNECT CONNECTOR Click here

    OK

    REPLACE NO. 8 JUNCTION CONNECTOR

37. CONNECT CONNECTOR

    
    

    1. Reconnect the E70 No. 10 junction connector.

    
    

    NEXT

38. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)

    
    
    1. 

       Text in Illustration

       *1	Front view of wire harness connector (to Combination Meter Assembly)
       *2	DLC3

       Disconnect the E77 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E77-37 (MPX+) - E77-38 (MPX-) Engine switch off 108 to 132 Ω E77-37 (MPX+) - E22-4 (CG) Engine switch off 200 Ω or higher E77-38 (MPX-) - E22-4 (CG) Engine switch off 200 Ω or higher E77-37 (MPX+) - E22-16 (BAT) Engine switch off 6 kΩ or higher E77-38 (MPX-) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (MPX+, MPX-)

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

39. CONNECT CONNECTOR

    
    

    1. Reconnect the E76 No. 9 junction connector.

    
    

    NEXT

40. CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to Position Control ECU and Switch)
       *2	DLC3

       Disconnect the c58 position control ECU and switch connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition c58-8 (MPX1) - c58-7 (MPX2) Engine switch off 54 to 69 Ω c58-8 (MPX1) - E22-4 (CG) Engine switch off 200 Ω or higher c58-7 (MPX2) - E22-4 (CG) Engine switch off 200 Ω or higher c58-8 (MPX1) - E22-16 (BAT) Engine switch off 6 kΩ or higher c58-7 (MPX2) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPLACE CAN BRANCH WIRE CONNECTED TO POSITION CONTROL ECU AND SWITCH (MPX1, MPX2)

    OK

    REPLACE POSITION CONTROL ECU AND SWITCH Click here

41. CONNECT CONNECTOR

    
    

    1. Reconnect the E76 No. 9 junction connector.

    
    

    NEXT

42. CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)

    
    
    1. 

       Text in Illustration

       *1	Front view of wire harness connector (to Multiplex Tilt and Telescopic ECU)
       *2	DLC3

       Disconnect the E27 power tilt and telescopic ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E27-5 (CANP) - E27-14 (CANN) Engine switch off 54 to 69 Ω E27-5 (CANP) - E22-4 (CG) Engine switch off 200 Ω or higher E27-14 (CANN) - E22-4 (CG) Engine switch off 200 Ω or higher E27-5 (CANP) - E22-16 (BAT) Engine switch off 6 kΩ or higher E27-14 (CANN) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN)

    OK

    REPLACE MULTIPLEX TILT AND TELESCOPIC ECU Click here

43. CONNECT CONNECTOR

    
    

    1. Reconnect the E76 No. 9 junction connector.

    
    

    NEXT

44. CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)

    
    
    1. 

       Text in Illustration

       *1	Front view of wire harness connector (to Outer Mirror Control ECU Assembly)
       *2	DLC3

       Disconnect the I32 outer mirror control ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition I32-1 (CANH) - I32-21 (CANL) Engine switch off 54 to 69 Ω I32-1 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher I32-21 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher I32-1 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher I32-21 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY (CANH, CANL)

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY Click here

45. CONNECT CONNECTOR

    
    

    1. Reconnect the E76 No. 9 junction connector.

    
    

    NEXT

46. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)

    
    
    1. 

       Text in Illustration

       *1	Front view of wire harness connector (to Certification ECU [Smart Key ECU Assembly])
       *2	DLC3

       Disconnect the E29 certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E29-27 (CANH) - E29-28 (CANL) Engine switch off 54 to 69 Ω E29-27 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E29-28 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E29-27 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E29-28 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

47. CONNECT CONNECTOR

    
    

    1. Reconnect the L29, L30 and L45 No. 2 CAN junction connectors.

    
    

    NEXT

48. CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to Power Back Door Unit Assembly [Power Back Door ECU])
       *2	DLC3

       Disconnect the L36 power back door unit assembly (power back door ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition L36-6 (MPX1) - L36-5 (MPX2) Engine switch off 54 to 69 Ω L36-6 (MPX1) - E22-4 (CG) Engine switch off 200 Ω or higher L36-5 (MPX2) - E22-4 (CG) Engine switch off 200 Ω or higher L36-6 (MPX1) - E22-16 (BAT) Engine switch off 6 kΩ or higher L36-5 (MPX2) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (MPX1, MPX2)

    OK

    REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) Click here

49. CONNECT CONNECTOR

    
    

    1. Reconnect the L29, L30, L45 and L46 No. 2 CAN junction connectors.

    
    

    NEXT

50. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 MAIN BODY ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to No. 2 Main Body ECU)
       *2	DLC3

       Disconnect the L33 No. 2 main body ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition L33-11 (MPX+) - L33-12 (MPX-) Engine switch off 54 to 69 Ω L33-11 (MPX+) - E22-4 (CG) Engine switch off 200 Ω or higher L33-12 (MPX-) - E22-4 (CG) Engine switch off 200 Ω or higher L33-11 (MPX+) - E22-16 (BAT) Engine switch off 6 kΩ or higher L33-12 (MPX-) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NO. 2 MAIN BODY ECU (MPX+, MPX-)

    OK

    REPLACE NO. 2 MAIN BODY ECU Click here

51. CONNECT CONNECTOR

    
    

    1. Reconnect the E73 No. 8 junction connector.

    
    

    NEXT

52. CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER ECU)

    
    
    1. 

       Text in Illustration

       *1	Front view of wire harness connector (to Windshield Wiper ECU)
       *2	DLC3

       Disconnect the E90 windshield wiper ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E90-6 (CANH) - E90-5 (CANL) Engine switch off 54 to 69 Ω E90-6 (CANH) - E22-4 (CG) Engine switch off 200 Ω or higher E90-5 (CANL) - E22-4 (CG) Engine switch off 200 Ω or higher E90-6 (CANH) - E22-16 (BAT) Engine switch off 6 kΩ or higher E90-5 (CANL) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO WINDSHIELD WIPER ECU (CANH, CANL)

    OK

    REPLACE WINDSHIELD WIPER ECU Click here

53. CONNECT CONNECTOR

    
    

    1. Reconnect the E73 No. 8 junction connector.

    
    

    NEXT

54. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

    
    
    1. 

       Text in Illustration

       *1	Rear view of wire harness connector (to Main Body ECU [Cowl Side Junction Block LH])
       *2	DLC3

       Disconnect the E3 main body ECU (cowl side junction block LH) connector.

    2. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Switch Condition Specified Condition E3-16 (CANP) - E3-15 (CANN) Engine switch off 108 to 132 Ω E3-16 (CANP) - E22-4 (CG) Engine switch off 200 Ω or higher E3-15 (CANN) - E22-4 (CG) Engine switch off 200 Ω or higher E3-16 (CANP) - E22-16 (BAT) Engine switch off 6 kΩ or higher E3-15 (CANN) - E22-16 (BAT) Engine switch off 6 kΩ or higher

    
    

    NG

    REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

    OK

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

55. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

    
    

    1. Connect the cable to the negative (-) battery terminal.

       

       Text in Illustration

       *1

       Front view of wire harness connector (to Main Body ECU [Cowl Side Junction Block LH])

       *2

       Rear view of wire harness connector (to Main Body ECU [Cowl Side Junction Block LH])

       Note

       When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    2. Disconnect the 2A, 2D and E3 main body ECU (cowl side junction block LH) connectors.

    3. Measure the voltage according to the value(s) in the table below.

       Standard Voltage
       Tester Connection Condition Specified Condition 2A-1 (ALTB) - Body ground Always 11 to 14 V

    4. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition 2D-62 (GND2) - Body ground Always Below 1 Ω E3-1 (GND3) - Body ground Always Below 1 Ω

    
    

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)