REAR BUMPER (for Standard) REASSEMBLY


  1. INSTALL REAR BUMPER PAD LH

    Tech Tips

    When installing the rear bumper pad LH, heat the rear bumper surface using a heat light.

    Standard
    Item Temperature
    Rear Bumper 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper excessively.


    1. Clean the rear bumper surface.


      1. Using a heat light, heat the rear bumper surface.

      2. Remove the double-sided tape from the rear bumper.

      3. Wipe off any tape adhesive residue with cleaner.

    2. A01EREH

      Install a new rear bumper pad LH.


      1. Remove the peeling paper from the face of new rear bumper pad LH.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. Install the rear bumper pad LH as shown in the illustration.

  2. INSTALL REAR BUMPER PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL REAR LOWER BUMPER COVER


    1. Attach the 6 claws.

    2. Install the rear lower bumper cover with the 2 clips.

  4. INSTALL REAR FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light)


    1. Connect the connector.

    2. Attach the clamp.

    3. Install the rear fog light assembly LH with the 3 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  5. INSTALL REAR FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light)

    Tech Tips

    Use the same procedure described for the LH side.

  6. INSTALL REFLEX REFLECTOR ASSEMBLY LH (w/o Rear Fog Light)


    1. Install the reflex reflector assembly LH with the 3 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  7. INSTALL REFLEX REFLECTOR ASSEMBLY RH (w/o Rear Fog Light)

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL REAR BUMPER ENERGY ABSORBER


    1. Attach the 8 claws to install the rear bumper energy absorber.

  9. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER

    Tech Tips

    Use the same procedure to install the No. 1 ultrasonic sensor retainer on the other side.


    1. A01ESGIE01
      Text in Illustration
      *a Protrusion
      *b Keyhole

      Align the keyhole and protrusion as shown in the illustration.

      Note


      • Do not damage the bumper with the protrusion when installing the No. 1 ultrasonic sensor retainer.

      • Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the rear bumper.

    2. Attach the 2 claws to install the No. 1 ultrasonic sensor retainer.

  10. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER

    Tech Tips

    Use the same procedure to install the No. 2 ultrasonic sensor retainer on the other side.


    1. A01ERC3E01
      Text in Illustration
      *a Protrusion
      *b Keyhole

      Align the keyhole and protrusion as shown in the illustration.

      Note


      • Do not damage the bumper with the protrusion when installing the No. 1 ultrasonic sensor retainer.

      • Securely install the No. 2 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the rear bumper.

    2. Attach the 2 claws to install the No. 2 ultrasonic sensor retainer.

  11. INSTALL NO. 1 ULTRASONIC SENSOR

    Tech Tips

    Use the same procedure for all No. 1 ultrasonic sensors.


    1. Attach the 2 claws to install the No. 1 ultrasonic sensor.

      Note

      Push the ultrasonic sensor retainer from the outside of the bumper when there is a gap between the retainer and the bumper surface. In this case, do not push on the ultrasonic sensor.

  12. INSTALL NO. 2 FRAME WIRE


    1. w/ Rear Fog Light:

      Install the No. 2 frame wire.


      1. Attach the 12 clamps to install the frame wire.

      2. Connect the 6 connectors.

    2. w/o Rear Fog Light:

      Install the No. 2 frame wire.


      1. Attach the 10 clamps to install the frame wire.

      2. Connect the 4 connectors.