CAN COMMUNICATION SYSTEM (for LHD) TERMINALS OF ECU

Tech Tips

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note


      • Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the engine switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

      • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. JUNCTION CONNECTOR


    1. NO. 1 JUNCTION CONNECTOR

      A01ERD4E96
      Text in Illustration
      *1 to Center Airbag Sensor Assembly *2 to Headlight Swivel ECU Assembly (AFS ECU)
      *3 to ECM *4 to No. 2 Junction Connector
      No. 1 Junction Connector Wiring Color Connect to
      E72-1 (CANH) SB No. 2 junction connector
      E72-12 (CANL) B
      E72-2 (CANH) P ECM
      E72-13 (CANL) B
      E72-3 (CANH) LG Headlight swivel ECU assembly (AFS ECU)
      E72-14 (CANL) B
      E72-4 (CANH) GR Center airbag sensor assembly
      E72-15 (CANL) B

    2. NO. 2 JUNCTION CONNECTOR

      A01ERD4E97
      Text in Illustration
      *1 to Air Conditioning Amplifier Assembly *2 to No. 3 Junction Connector
      *3 to Network Gateway ECU: V Bus *4 to Multi-media Module Receiver Assembly
      *5 to No. 1 Junction Connector - -
      No. 2 Junction Connector Wiring Color Connect to
      E69-1 (CANH) SB No. 1 junction connector
      E69-12 (CANL) B
      E69-2 (CANH) P Multi-media module receiver assembly
      E69-13 (CANL) B
      E69-3 (CANH) BE Network gateway ECU (V bus)
      E69-14 (CANL) B
      E69-4 (CANH) SB No. 3 junction connector
      E69-15 (CANL) B
      E69-5 (CANH) G Air conditioning amplifier assembly
      E69-16 (CANL) B

    3. NO. 3 JUNCTION CONNECTOR

      A01ERD4E98
      Text in Illustration
      *1 to Main Body ECU (Cowl Side Junction Block LH): V Bus *2 to Combination Meter Assembly: V Bus
      *3 to DLC3 *4 to No. 2 Junction Connector
      No. 3 Junction Connector Wiring Color Connect to
      E75-1 (CANH) SB No. 2 junction connector
      E75-12 (CANL) B
      E75-2 (CANH) G DLC3
      E75-13 (CANL) B
      E75-3 (CANH) V Combination meter assembly (V bus)
      E75-14 (CANL) B
      E75-4 (CANH) SB Main body ECU (cowl side junction block LH) (V bus)
      E75-15 (CANL) B

    4. NO. 4 JUNCTION CONNECTOR

      A01ERD4E99
      Text in Illustration
      *1 to 4WD Control ECU *2 to Network Gateway ECU: Movement Control Bus
      *3 to No. 5 Junction Connector - -
      No. 4 Junction Connector Wiring Color Connect to
      E71-1 (CANH) W No. 5 junction connector
      E71-12 (CANL) L
      E71-2 (CANH) SB Network gateway ECU (movement control bus)
      E71-13 (CANL) L
      E71-3 (CANH) P 4WD control ECU
      E71-14 (CANL) L

    5. NO. 5 JUNCTION CONNECTOR

      A01ER7SE01
      Text in Illustration
      *1

      to Seat Belt Control ECU

      (w/ Pre-crash Safety System)

      		 *2

      to Display Control ECU Assembly

      (w/ Dynamic Radar Cruise Control System)
      *3 to Yaw Rate Sensor Assembly *4 to No. 6 Junction Connector
      *5 to No. 4 Junction Connector - -
      No. 5 Junction Connector Wiring Color Connect to
      E68-1 (CANH) W No. 4 junction connector
      E68-12 (CANL) L
      E68-2 (CANH) SB No. 6 junction connector
      E68-13 (CANL) L
      E68-3 (CANH) BR Yaw rate sensor assembly
      E68-14 (CANL) L
      E68-4 (CANH) SB Distance control ECU assembly*1
      E68-15 (CANL) L
      E68-5 (CANH) G Seat belt control ECU*2
      E68-16 (CANL) L

      • *1: w/ Dynamic Radar Cruise Control System

      • *2: w/ Pre-crash Safety System

    6. NO. 6 JUNCTION CONNECTOR

      A01EPVME02
      Text in Illustration
      *1 to No. 5 Junction Connector *2 to No. 7 Junction Connector
      *3

      • to Clearance Warning ECU Assembly

        (w/o Side Monitor System)

      • to Parking Assist ECU

        (w/ Side Monitor System)

      		 - -
      No. 6 Junction Connector Wiring Color Connect to
      F79-5 (CANH) V

      • Clearance warning ECU assembly*1

      • Parking assist ECU*2
      F79-16 (CANL) L
      F79-6 (CANH) SB No. 7 junction connector
      F79-17 (CANL) L
      F79-7 (CANH) SB No. 5 junction connector
      F79-18 (CANL) L

      • *1: w/o Side Monitor System

      • *2: w/ Side Monitor System

    7. NO. 7 JUNCTION CONNECTOR

      A01ER7SE02
      Text in Illustration
      *1 to Master Cylinder Solenoid (Skid Control ECU) *2 to Steering Angle Sensor
      *3 to Steering Control ECU *4 to No. 6 Junction Connector
      *5 to No. 1 CAN Junction Connector - -
      No. 7 Junction Connector Wiring Color Connect to
      E74-1 (CANH) W No. 1 CAN junction connector
      E74-12 (CANL) L
      E74-2 (CANH) SB No. 6 junction connector
      E74-13 (CANL) L
      E74-3 (CANH) LG Steering control ECU
      E74-14 (CANL) L
      E74-4 (CANH) GR Steering angle sensor
      E74-15 (CANL) L
      E74-5 (CANH) V Master cylinder solenoid (skid control ECU)
      E74-16 (CANL) L

    8. NO. 8 JUNCTION CONNECTOR

      A01ER7SE03
      Text in Illustration
      *1 to Main Body ECU (Cowl Side Junction Block LH): MS Bus *2 to Outer Mirror Control ECU Assembly
      *3 to Position Control ECU and Switch *4 to Multiplex Tilt and Telescopic ECU
      *5 to Certification ECU (Smart Key ECU Assembly) *6 to No. 2 CAN Junction Connector
      No. 8 Junction Connector Wiring Color Connect to
      E76-1 (CANH) W No. 2 CAN junction connector
      E76-12 (CANL) R
      E76-2 (CANH) LG Certification ECU (smart key ECU assembly)
      E76-13 (CANL) R
      E76-3 (CANH) P Multiplex tilt and telescopic ECU
      E76-14 (CANL) R
      E76-4 (CANH) V Position control ECU and switch
      E76-15 (CANL) R
      E76-5 (CANH) BR Outer mirror control ECU assembly
      E76-16 (CANL) R
      E76-6 (CANH) GR Main body ECU (cowl side junction block LH) (MS bus)
      E76-17 (CANL) R

    9. NO. 9 JUNCTION CONNECTOR

      A01ER7SE04
      Text in Illustration
      *1 to Windshield Wiper ECU *2 to No. 2 CAN Junction Connector
      *3 to No. 10 Junction Connector - -
      No. 9 Junction Connector Wiring Color Connect to
      E73-1 (CANH) W No. 10 junction connector
      E73-12 (CANL) R
      E73-2 (CANH) Y No. 2 CAN junction connector
      E73-13 (CANL) R
      E73-4 (CANH) LG Windshield wiper ECU
      E73-15 (CANL) R

    10. NO. 10 JUNCTION CONNECTOR

      A01ER7SE05
      Text in Illustration
      *1 to Combination Meter Assembly: MS Bus *2 to No. 9 Junction Connector
      No. 10 Junction Connector Wiring Color Connect to
      E70-1 (CANH) W No. 9 Junction Connector
      E70-12 (CANL) R
      E70-3 (CANH) LG Combination meter assembly (MS bus)
      E70-14 (CANL) R

    11. NO. 1 CAN JUNCTION CONNECTOR

      A01EN92E07
      Junction Connector A Side Wiring Color (CANH Side) Wiring Color (CANL Side)
      Body ground (K28) - W-B
      No. 7 junction connector (K29) W L
      Suspension control ECU (K41) V L

    12. NO. 2 CAN JUNCTION CONNECTOR

      A01EN92E16
      Junction Connector B Side Wiring Color (CANH Side) Wiring Color (CANL Side)
      No. 8 junction connector (L29) LG GR
      No. 9 junction connector (L30) Y R
      Power back door unit assembly (power back door ECU) (L45)* V R
      No. 2 main body ECU (L46) LG R
      Tire pressure warning ECU (L64) G R

      • *: w/ Power Back Door System

  3. TERMINALS OF CONNECTORS FOR JUNCTION CONNECTOR (CAN JUNCTION CONNECTOR)

    A01EPBG
    Terminal No. Symbol
    1 CANH
    2 CANL

  4. CHECK DLC3


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    2. A01ERIWE08

      Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E22-6 (CANH) - E22-14 (CANL) G - B Engine switch off 54 to 69 Ω
      E22-6 (CANH) - E22-4 (CG) G - W-B Engine switch off 200 Ω or higher
      E22-14 (CANL) - E22-4 (CG) B - W-B Engine switch off 200 Ω or higher
      E22-6 (CANH) - E22-16 (BAT) G - BE Engine switch off 6 kΩ or higher
      E22-14 (CANL) - E22-16 (BAT) B - BE Engine switch off 6 kΩ or higher

  5. CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

    A01EO62E01

    1. Disconnect the A24 master cylinder solenoid (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A24-11 (CANH) - A24-25 (CANL) V - L Engine switch off 54 to 69 Ω
      A24-11 (CANH) - A24-1 (GND1) V - W-B Engine switch off 200 Ω or higher
      A24-25 (CANL) - A24-1 (GND1) L - W-B Engine switch off 200 Ω or higher
      A24-11 (CANH) - A24-2 (+BM1) V - B Engine switch off 6 kΩ or higher
      A24-25 (CANL) - A24-2 (+BM1) L - B Engine switch off 6 kΩ or higher

  6. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

    A01ES9XE06

    1. Disconnect the E35 and E36 air conditioning amplifier assembly connectors.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Condition Specified Condition
      E35-3 (CANH) - E35-4 (CANL) G - B Engine switch off 54 to 69 Ω
      E35-3 (CANH) - E36-1 (GND) G - W-B Engine switch off 200 Ω or higher
      E35-4 (CANL) - E36-1 (GND) B - W-B Engine switch off 200 Ω or higher
      E35-3 (CANH) - E36-6 (+B1) G - R Engine switch off 6 kΩ or higher
      E35-4 (CANL) - E36-6 (+B1) B - R Engine switch off 6 kΩ or higher

  7. CHECK ECM

    A01EQOAE03

    1. Disconnect the A38 and C53 ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A38-10 (CANH) - A38-11 (CANL) P - B Engine switch off 108 to 132 Ω
      A38-10 (CANH) - C53-81 (E1) P - W-B Engine switch off 200 Ω or higher
      A38-11 (CANL) - C53-81 (E1) B - W-B Engine switch off 200 Ω or higher
      A38-10 (CANH) - A38-3 (+B) P - B Engine switch off 6 kΩ or higher
      A38-11 (CANL) - A38-3 (+B) B - B Engine switch off 6 kΩ or higher

  8. CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

    A01EOYJE01

    1. Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.

    2. Measure the resistance according to the value(s) in the table below.

      V Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E3-5 (CANH) - E3-6 (CANL) SB - B Engine switch off 54 to 69 Ω
      E3-5 (CANH) - 2D-62 (GND2) SB - W-B Engine switch off 200 Ω or higher
      E3-6 (CANL) - 2D-62 (GND2) B - W-B Engine switch off 200 Ω or higher
      E3-5 (CANH) - 2A-1 (ALTB) SB - B Engine switch off 6 kΩ or higher
      E3-6 (CANL) - 2A-1 (ALTB) B - B Engine switch off 6 kΩ or higher
      MS Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E3-16 (CANP) - E3-15 (CANN) GR - R Engine switch off 108 to 132 Ω
      E3-16 (CANP) - 2D-62 (GND2) GR - W-B Engine switch off 200 Ω or higher
      E3-15 (CANN) - 2D-62 (GND2) R - W-B Engine switch off 200 Ω or higher
      E3-16 (CANP) - 2A-1 (ALTB) GR - B Engine switch off 6 kΩ or higher
      E3-15 (CANN) - 2A-1 (ALTB) R - B Engine switch off 6 kΩ or higher

  9. CHECK COMBINATION METER ASSEMBLY

    A01ERIQE02

    1. Disconnect the E77 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      V Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E77-36 (CANH) - E77-35 (CANL) V - B Engine switch off 108 to 132 Ω
      E77-36 (CANH) - E77-20 (EP) V - W-B Engine switch off 200 Ω or higher
      E77-35 (CANL) - E77-20 (EP) B - W-B Engine switch off 200 Ω or higher
      E77-36 (CANH) - E77-21 (B) V - R Engine switch off 6 kΩ or higher
      E77-35 (CANL) - E77-21 (B) B - R Engine switch off 6 kΩ or higher
      MS Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E77-37 (MPX+) - E77-38 (MPX-) LG - R Engine switch off 108 to 132 Ω
      E77-37 (MPX+) - E77-20 (EP) LG - W-B Engine switch off 200 Ω or higher
      E77-38 (MPX-) - E77-20 (EP) R - W-B Engine switch off 200 Ω or higher
      E77-37 (MPX+) - E77-21 (B) LG - R Engine switch off 6 kΩ or higher
      E77-38 (MPX-) - E77-21 (B) R - R Engine switch off 6 kΩ or higher

  10. CHECK CENTER AIRBAG SENSOR ASSEMBLY

    A01ESGZE02

    1. Disconnect the E47 center airbag sensor assembly connector Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E47-13 (CANH) - E47-22 (CANL) GR - B Engine switch off 54 to 69 Ω
      E47-13 (CANH) - E47-25 (E1) GR - W-B Engine switch off 200 Ω or higher
      E47-22 (CANL) - E47-25 (E1) B - W-B Engine switch off 200 Ω or higher
      E47-13 (CANH) - E22-16 (BAT) GR - BE Engine switch off 6 kΩ or higher
      E47-22 (CANL) - E22-16 (BAT) B - BE Engine switch off 6 kΩ or higher

  11. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

    A01EO0PE39

    1. Disconnect the F76 multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F76-1 (CANH) - F76-2 (CANL) P - B Engine switch off 54 to 69 Ω
      F76-1 (CANH) - F76-12 (GND1) P - W-B Engine switch off 200 Ω or higher
      F76-2 (CANL) - F76-12 (GND1) B - W-B Engine switch off 200 Ω or higher
      F76-1 (CANH) - F76-17 (+B1) P - R Engine switch off 6 kΩ or higher
      F76-2 (CANL) - F76-17 (+B1) B - R Engine switch off 6 kΩ or higher

  12. CHECK STEERING ANGLE SENSOR

    A01EQOHE03

    1. Disconnect the E11 steering angle sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E11-10 (CANH) - E11-9 (CANL) GR - L Engine switch off 54 to 69 Ω
      E11-10 (CANH) - E11-2 (ESS) GR - W-B Engine switch off 200 Ω or higher
      E11-9 (CANL) - E11-2 (ESS) L - W-B Engine switch off 200 Ω or higher
      E11-10 (CANH) - E22-16 (BAT) GR - BE Engine switch off 6 kΩ or higher
      E11-9 (CANL) - E22-16 (BAT) L - BE Engine switch off 6 kΩ or higher

  13. CHECK YAW RATE SENSOR ASSEMBLY

    A01EOR3E02

    1. Disconnect the E50 yaw rate sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E50-3 (CANH) - E50-2 (CANL) BR - L Engine switch off 54 to 69 Ω
      E50-3 (CANH) - E50-1 (GND) BR - W-B Engine switch off 200 Ω or higher
      E50-2 (CANL) - E50-1 (GND) L - W-B Engine switch off 200 Ω or higher
      E50-3 (CANH) - E22-16 (BAT) BR - BE Engine switch off 6 kΩ or higher
      E50-2 (CANL) - E22-16 (BAT) L - BE Engine switch off 6 kΩ or higher

  14. CHECK SEAT BELT CONTROL ECU (w/ Pre-crash Safety System)

    A01ESOPE03

    1. Disconnect the E41 and E42 seat belt control ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E42-1 (CANH) - E42-2 (CANL) G - L Engine switch off 54 to 69 Ω
      E42-1 (CANH) - E41-8 (PGND) G - W-B Engine switch off 200 Ω or higher
      E42-2 (CANL) - E41-8 (PGND) L - W-B Engine switch off 200 Ω or higher
      E42-1 (CANH) - E41-7 (+B) G - R Engine switch off 6 kΩ or higher
      E42-2 (CANL) - E41-7 (+B) L - R Engine switch off 6 kΩ or higher

  15. CHECK OUTER MIRROR CONTROL ECU ASSEMBLY

    A01EOLQE04

    1. Disconnect the I18 and I17 outer mirror control ECU assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      I18-1 (CANH) - I18-21 (CANL) BR - R Engine switch off 54 to 69 Ω
      I18-1 (CANH) - I17-9 (GND) BR - W-B Engine switch off 200 Ω or higher
      I18-21 (CANL) - I17-9 (GND) R - W-B Engine switch off 200 Ω or higher
      I18-1 (CANH) - I17-3 (B) BR - R Engine switch off 6 kΩ or higher
      I18-21 (CANL) - I17-3 (B) R - R Engine switch off 6 kΩ or higher

  16. CHECK MULTIPLEX TILT AND TELESCOPIC ECU

    A01EQ1YE03

    1. Disconnect the E27 multiplex tilt and telescopic ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E27-5 (CANP) - E27-14 (CANN) P - R Engine switch off 54 to 69 Ω
      E27-5 (CANP) - E27-11 (GND) P - W-B Engine switch off 200 Ω or higher
      E27-14 (CANN) - E27-11 (GND) R - W-B Engine switch off 200 Ω or higher
      E27-5 (CANP) - E27-2 (+B) P - L Engine switch off 6 kΩ or higher
      E27-14 (CANN) - E27-2 (+B) R - L Engine switch off 6 kΩ or higher

  17. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    A01ENKIE04

    1. Disconnect the E29 certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E29-27 (CANH) - E29-28 (CANL) LG - R Engine switch off 54 to 69 Ω
      E29-27 (CANH) - E29-17 (E) LG - W-B Engine switch off 200 Ω or higher
      E29-28 (CANL) - E29-17 (E) R - W-B Engine switch off 200 Ω or higher
      E29-27 (CANH) - E29-1 (+B) LG - B Engine switch off 6 kΩ or higher
      E29-28 (CANL) - E29-1 (+B) R - B Engine switch off 6 kΩ or higher

  18. CHECK POSITION CONTROL ECU AND SWITCH

    A01EN8HE46

    1. Disconnect the c62 and c63 position control ECU and switch connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      c63-8 (MPX1) - c63-7 (MPX2) V - R Engine switch off 54 to 69 Ω
      c63-8 (MPX1) - c62-1 (GND) V - W-B Engine switch off 200 Ω or higher
      c63-7 (MPX2) - c62-1 (GND) R - W-B Engine switch off 200 Ω or higher
      c63-8 (MPX1) - c62-6 (+B) V - L Engine switch off 6 kΩ or higher
      c63-7 (MPX2) - c62-6 (+B) R - L Engine switch off 6 kΩ or higher

  19. CHECK 4WD CONTROL ECU

    A01ES7RE03

    1. Disconnect the A27 and A28 4WD control ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      A27-19 (CAN+) - A27-20 (CAN-) P - L Engine switch off 54 to 69 Ω
      A27-19 (CAN+) - A28-4 (GND) P - W Engine switch off 200 Ω or higher
      A27-20 (CAN-) - A28-4 (GND) L - W Engine switch off 200 Ω or higher
      A27-19 (CAN+) - E22-16 (BAT) P - BE Engine switch off 6 kΩ or higher
      A27-20 (CAN-) - E22-16 (BAT) L - BE Engine switch off 6 kΩ or higher

  20. CHECK NETWORK GATEWAY ECU

    A01ERHNE01

    1. Disconnect the E31 network gateway ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      V Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E31-16 (CA1H) - E31-15 (CA1L) BE - B Engine switch off 54 to 69 Ω
      E31-16 (CA1H) - E31-4 (GND) BE - W-B Engine switch off 200 Ω or higher
      E31-15 (CA1L) - E31-4 (GND) B - W-B Engine switch off 200 Ω or higher
      E31-16 (CA1H) - E31-2 (BATT) BE - R Engine switch off 6 kΩ or higher
      E31-15 (CA1L) - E31-2 (BATT) B - R Engine switch off 6 kΩ or higher
      Movement Control Bus
      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E31-13 (CA2H) - E31-12 (CA2L) SB - L Engine switch off 108 to 132 Ω
      E31-13 (CA2H) - E31-4 (GND) SB - W-B Engine switch off 200 Ω or higher
      E31-12 (CA2L) - E31-4 (GND) L - W-B Engine switch off 200 Ω or higher
      E31-13 (CA2H) - E31-2 (BATT) SB - R Engine switch off 6 kΩ or higher
      E31-12 (CA2L) - E31-2 (BATT) L - R Engine switch off 6 kΩ or higher

  21. CHECK STEERING CONTROL ECU

    A01EQTOE17

    1. Disconnect the E82 and E84 steering control ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E84-9 (CANH) - E84-20 (CANL) LG - L Engine switch off 200 Ω or higher
      E84-9 (CANH) - E82-7 (PGND) LG - W-B Engine switch off 200 Ω or higher
      E84-20 (CANL) - E82-7 (PGND) L - W-B Engine switch off 200 Ω or higher
      E84-9 (CANH) - E82-10 (+BI) LG - R Engine switch off 6 kΩ or higher
      E84-20 (CANL) - E82-10 (+BI) L - R Engine switch off 6 kΩ or higher

  22. CHECK SUSPENSION CONTROL ECU

    A01EOROE07

    1. Disconnect the K30 suspension control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      K30-7 (CANH) - K30-8 (CANL) V - L Engine switch off 54 to 69 Ω
      K30-7 (CANH) - K30-1 (GND) V - W-B Engine switch off 200 Ω or higher
      K30-8 (CANL) - K30-1 (GND) L - W-B Engine switch off 200 Ω or higher
      K30-7 (CANH) - K30-3 (BAT2) V - R Engine switch off 6 kΩ or higher
      K30-8 (CANL) - K30-3 (BAT2) L - R Engine switch off 6 kΩ or higher

  23. CHECK WINDSHIELD WIPER ECU

    A01EPOWE02

    1. Disconnect the E90 windshield wiper ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E90-6 (CANH) - E90-5 (CANL) LG - R Engine switch off 54 to 69 Ω
      E90-6 (CANH) - E90-10 (E) LG - W-B Engine switch off 200 Ω or higher
      E90-5 (CANL) - E90-10 (E) R - W-B Engine switch off 200 Ω or higher
      E90-6 (CANH) - E22-16 (BAT) LG - BE Engine switch off 6 kΩ or higher
      E90-5 (CANL) - E22-16 (BAT) R - BE Engine switch off 6 kΩ or higher

  24. CHECK CLEARANCE WARNING ECU ASSEMBLY (w/o Side Monitor System)

    A01EN4LE02

    1. Disconnect F12 clearance warning ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F12-3 (CANH) - F12-5 (CANL) V - L Engine switch off 54 to 69 Ω
      F12-3 (CANH) - F12-17 (GND1) V - W-B Engine switch off 200 Ω or higher
      F12-5 (CANL) - F12-17 (GND1) L - W-B Engine switch off 200 Ω or higher
      F12-3 (CANH) - E22-16 (BAT) V - BE Engine switch off 6 kΩ or higher
      F12-5 (CANL) - E22-16 (BAT) L - BE Engine switch off 6 kΩ or higher

  25. CHECK PARKING ASSIST ECU (w/ Side Monitor System)

    A01ESB2E12

    1. Disconnect the F74 and F75 parking assist ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      F75-40 (CANH) - F75-39 (CANL) V - L Engine switch off 54 to 69 Ω
      F75-40 (CANH) - F74-4 (GND1) V - W-B Engine switch off 200 Ω or higher
      F75-39 (CANL) - F74-4 (GND1) L - W-B Engine switch off 200 Ω or higher
      F75-40 (CANH) - F74-1 (+B) V - L Engine switch off 6 kΩ or higher
      F75-39 (CANL) - F74-1 (+B) L - L Engine switch off 6 kΩ or higher

  26. CHECK DISTANCE CONTROL ECU ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    A01EQMGE01

    1. Disconnect the E86 distance control ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E86-8 (CANH) - E86-9 (CANL) SB - L Engine switch off 54 to 69 Ω
      E86-8 (CANH) - E86-12 (GND) SB - BR Engine switch off 200 Ω or higher
      E86-9 (CANL) - E86-12 (GND) L - BR Engine switch off 200 Ω or higher
      E86-8 (CANH) - E86-1 (B) SB - R Engine switch off 6 kΩ or higher
      E86-9 (CANL) - E86-1 (B) L - R Engine switch off 6 kΩ or higher

  27. CHECK POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (w/ Power Back Door System)

    A01EQMGE02

    1. Disconnect the L36 power back door unit assembly (power back door ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L36-6 (MPX1) - L36-5 (MPX2) V - R Engine switch off 54 to 69 Ω
      L36-6 (MPX1) - L36-11 (GND) V - W-B Engine switch off 200 Ω or higher
      L36-5 (MPX2) - L36-11 (GND) R - W-B Engine switch off 200 Ω or higher
      L36-6 (MPX1) - L36-10 (ECUB) V - R Engine switch off 6 kΩ or higher
      L36-5 (MPX2) - L36-10 (ECUB) R - R Engine switch off 6 kΩ or higher

  28. CHECK TIRE PRESSURE WARNING ECU

    A01EPHUE05

    1. Disconnect the L63 tire pressure warning ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L63-3 (CP1) - L63-6 (CN1) W - B Engine switch off 54 to 69 Ω
      L63-3 (CP1) - L63-4 (GN1) W - G Engine switch off 200 Ω or higher
      L63-6 (CN1) - L63-4 (GN1) B - G Engine switch off 200 Ω or higher
      L63-3 (CP1) - E22-16 (BAT) W - BE Engine switch off 6 kΩ or higher
      L63-6 (CN1) - E22-16 (BAT) B - BE Engine switch off 6 kΩ or higher

  29. CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (AFS ECU)

    A01EQP4E06

    1. Disconnect the E91 headlight swivel ECU assembly (AFS ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      E91-12 (MPX1) - E91-13 (MPX2) LG - B Engine switch off 54 to 69 Ω
      E91-12 (MPX1) - E91-22 (E1) LG - W-B Engine switch off 200 Ω or higher
      E91-13 (MPX2) - E91-22 (E1) B - W-B Engine switch off 200 Ω or higher
      E91-12 (MPX1) - E22-16 (BAT) LG - BE Engine switch off 6 kΩ or higher
      E91-13 (MPX2) - E22-16 (BAT) B - BE Engine switch off 6 kΩ or higher

  30. CHECK NO. 2 MAIN BODY ECU

    A01ERE5E05

    1. Disconnect the L33 No. 2 main body ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
      L33-11 (MPX+) - L33-12 (MPX-) LG - R Engine switch off 54 to 69 Ω
      L33-11 (MPX+) - L33-7 (GND) LG - W-B Engine switch off 200 Ω or higher
      L33-12 (MPX-) - L33-7 (GND) R - W-B Engine switch off 200 Ω or higher
      L33-11 (MPX+) - L33-14 (BECU) LG - R Engine switch off 6 kΩ or higher
      L33-12 (MPX-) - L33-14 (BECU) R - R Engine switch off 6 kΩ or higher