SIDE MONITOR SYSTEM, Diagnostic DTC:C1683, C1684

DTC Code DTC Name
C1683 Side Camera Feedback Malfunction
C1684 Side Camera Current Malfunction

DESCRIPTION

DTC C1683 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly (for Front Passenger Side) to the parking assist ECU.

DTC C1684 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the side television camera assembly (for Front Passenger Side) connected to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1683 Side Camera Feedback Malfunction

  • Harness or connector

  • Parking assist ECU

  • Side television camera assembly (for Front Passenger Side)

  • Outer rear view mirror assembly (for Front Passenger Side)
C1684 Side Camera Current Malfunction

WIRING DIAGRAM

A01ERLOE01
A01ERLOE02

INSPECTION PROCEDURE

Note


  • When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed Click here.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY AND BODY GROUND)


    1. Disconnect the F74 and F75 parking assist ECU connectors.

    2. Disconnect the I35*1 or I33*2 outer rear view mirror assembly (for Front Passenger Side) connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      F75-34 (SCV-) - I35-12 (SCV-) Always Below 1 Ω
      F75-10 (SCV+) - I35-1 (SCV+) Always Below 1 Ω
      F75-33 (SGND) - I35-13 (SGND) Always Below 1 Ω
      F75-32 (SCB+) - I35-2 (SCB+) Always Below 1 Ω
      F74-4 (GND1) - Body ground Always Below 1 Ω
      F75-34 (SCV-) - Body ground Always 10 kΩ or higher
      F75-10 (SCV+) - Body ground Always 10 kΩ or higher
      F75-33 (SGND) - Body ground Always 10 kΩ or higher
      F75-32 (SCB+) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F75-34 (SCV-) - I33-12 (DCV-) Always Below 1 Ω
      F75-10 (SCV+) - I33-1 (DCV+) Always Below 1 Ω
      F75-33 (SGND) - I33-13 (DGND) Always Below 1 Ω
      F75-32 (SCB+) - I33-2 (DCB+) Always Below 1 Ω
      F74-4 (GND1) - Body ground Always Below 1 Ω
      F75-34 (SCV-) - Body ground Always 10 kΩ or higher
      F75-10 (SCV+) - Body ground Always 10 kΩ or higher
      F75-33 (SGND) - Body ground Always 10 kΩ or higher
      F75-32 (SCB+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK PARKING ASSIST ECU (SCB+, SGND)


    1. A01ENMWE03
      Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

      Reconnect the F74 and F75 parking assist ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F75-33 (SGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F75-32 (SCB+) - F75-33 (SGND) Engine switch on (IG), front and side monitor main switch assembly on 5.5 to 7.05 V

    NG

    REPLACE PARKING ASSIST ECU Click here

    OK

  3. CHECK OUTER REAR VIEW MIRROR ASSEMBLY (SCV+, SGND OR DCV+, DGND)


    1. Reconnect the I35*1 or I33*2 outer rear view mirror assembly (for Front Passenger Side) connector.


      • *1: for LHD

      • *2: for RHD

      A01ER52E03
      Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

      		 *b Waveform A
      *c Waveform B *d Synchronization Signal
      *e Video Waveform - -

      Tech Tips


      • A waterproof connector is used for the side television camera assembly (for Front Passenger Side). Therefore, inspect the waveform at the parking assist ECU with the connector connected.

      • The video waveform changes according to the image sent by the side television camera assembly (for Front Passenger Side).

    2. Measure the resistance according to the value(s) in the table below.

      OK
      Waveform is as shown in the illustration.
      Item Content
      Terminal No. (Symbol) F75-10 (SCV+) - F75-33 (SGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition

      • Waveform A: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is not covered, displaying an image

      • Waveform B: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is covered, blacking out the screen

    NG

    REPLACE SIDE TELEVISION CAMERA ASSEMBLY Click here

    OK

    REPLACE PARKING ASSIST ECU Click here

  4. REPLACE SIDE TELEVISION CAMERA ASSEMBLY


    1. Replace the side television camera assembly (for Front Passenger Side) with a new or normally functioning one Click here.


    NEXT

  5. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      OK
      DTC C1683 or C1684 is not output.

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY Click here

    OK

    END (SIDE TELEVISION CAMERA ASSEMBLY IS DEFECTIVE)