TELEVISION CAMERA (for Side) REMOVAL

Tech Tips

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Click here
REMOVE OUTER MIRROR LH
1. Push the upper part of the mirror surface and tilt it.
2. Using a moulding remover, detach the 4 claws and separate the outer rear view mirror glass from the mirror body.
  
  Tech Tips
  
  Apply protective tape to the outer rear view mirror to prevent it from being damaged.
3. Disconnect the 3 connectors and remove the mirror glass.

REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

Remove the outer mirror cover.

Tech Tips

Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.

Text in Illustration

*1 Protective Tape

Using 2 screwdrivers, detach the 2 claws.

Tech Tips

Tape the screwdriver tip before use.

Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

Note

Be careful not to break the ribs.

Tech Tips

Tape the screwdriver tip before use.

Text in Illustration
*1	Protective Tape	*2	Rib
*a	Inner Side of Outer Mirror Cover	-	-

Text in Illustration
*1	Protective Tape

Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

Note

Do not insert the moulding remover more than 4 mm (0.157 in.).

Tech Tips

Tape the moulding remover before use.

Standard

Area	Specified Condition
a	4mm

Text in Illustration
*1	Protective Tape

Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

Note

Do not insert the moulding remover more than 4 mm (0.157 in.).
Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

Standard

Area	Specified Condition
a	40mm
b	4mm

Remove the moulding remover B.

Text in Illustration
*1	Protective Tape
*a	Lower Side

Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

Insert a moulding remover B between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.
Text in Illustration

*1 Protective Tape

Using a screwdriver, detach the claw.
Detach the 2 claws and remove the outer mirror cover.

Note

When removing the cover, be careful not to damage the side turn signal light assembly or cover.

Remove the side turn signal light assembly LH.
1. Remove the 3 screws and side turn signal light assembly LH.
2. Disconnect the connector.

REMOVE SIDE TELEVISION CAMERA ASSEMBLY
1. Remove the gasket.
  1. Remove the tape.
  2. Detach the 9 guides and remove the gasket.
    
    Tech Tips
    
    Slightly lower the gasket so that the television camera assembly can be removed.
2. Remove the lower mirror cover.
  1. Text in Illustration
    
    *1 Protective Tape
    
    Using a screwdriver with its tip wrapped in protective tape, disconnect the 4 claws and remove the lower mirror cover.
3. Remove the base.
  1. Remove the wire harness.
  2. Using "TORX" socket wrench T25, remove the 3 screws.
    
    Note
    
    Make sure to replace the "TORX" screws with new ones.
  3. Disconnect the guide and remove the base.
4. Detach the connector from the wire clip.
5. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disconnect the connector.
  
  Tech Tips
  
  Tape the moulding remover before use.
6. Remove the body cover.
  1. Remove the 5 screws and body cover.
7. Remove the body.
  1. Disconnect the 2 guides and remove the body.
    
    Note
    
    Be careful not to break the guide shown in the part of the illustration labeled A.
8. Remove the 3 screws and side television camera assembly.