PARKING ASSIST MONITOR SYSTEM (w/o Side Monitor System) Image from Camera for Parking Assist Monitor is Abnormal

DESCRIPTION

The video signal from the rear television camera assembly is transmitted to the multi-media module receiver assembly.

WIRING DIAGRAM

A01EQQ9E17

INSPECTION PROCEDURE

Note


  • When "System initializing" is displayed on the multi-media module receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/o Side Monitor System) may be needed Click here.

Tech Tips

Images may be unclear even in normal conditions if:


  • Noise may occur in the image during power back door operation. (w/ Power Back Door System)

  • Electrical devices are used in the cabin (noise may occur in the image).

  • Accessories that generate radio waves have been installed (noise may occur in the image).

  • The outer mirror switch assembly is operated (noise may occur in the image).

  • The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

  • The camera lens is dirty with snow, mud, etc.

  • A strong beam of light, such as a sunbeam or headlight, hits the camera.

  • It is too dark around the camera (at night etc.).

  • The ambient temperature around the camera is either too high or too low.

  • The vehicle is tilted at a steep angle.

  • The rear television camera assembly lens is scratched.

  • The rear television camera assembly lens has drops of water on it or the humidity is high.

  • When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.

  • The ambience of the camera is too bright. (When a strong light, such as a sunbeam reflected off the vehicle body, hits the camera, the image may be blurred. This is called the "SMEAR" phenomenon, particular to the CCD camera.)

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY AND BODY GROUND)


    1. Disconnect the F76 multi-media module receiver assembly connector.

    2. Disconnect the S5 rear television camera assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F76-18 (V+) - S5-2 (CV+) Always Below 1 Ω
      F76-19 (V-) - S5-1 (CV-) Always Below 1 Ω
      F76-39 (CA+) - S5-4 (CB+) Always Below 1 Ω
      F76-40 (CGND) - S5-3 (CGND) Always Below 1 Ω
      F76-12 (GND1) - Body ground Always Below 1 Ω
      F76-18 (V+) - Body ground Always 10 kΩ or higher
      F76-19 (V-) - Body ground Always 10 kΩ or higher
      F76-39 (CA+) - Body ground Always 10 kΩ or higher
      F76-40 (CGND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CA+, CGND)


    1. A01EN77E04
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      Reconnect the multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F76-40 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F76-39 (CA+) - F76-40 (CGND) Engine switch on (IG), shift lever in R 5.5 to 7.05 V

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  3. CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND)


    1. Reconnect the S5 rear television camera assembly connector.

      A01ER1XE03
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      		 *b Waveform A
      *c Waveform B *d Synchronization Signal
      *e Video Waveform - -

    2. Check the waveform of the rear television camera assembly using an oscilloscope.

      Tech Tips


      • A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.

      • The video waveform changes according to the image sent by the rear television camera assembly.

      Item Content
      Terminal No. (Symbol) F76-18 (V+) - F76-40 (CGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition

      • Waveform A: Engine switch on (IG), shift lever in R and camera lens is not covered, displaying an image

      • Waveform B: Engine switch on (IG), shift lever in R and camera lens is covered, blacking out the screen
      OK
      Waveform is as shown in the illustration.

    NG

    REPLACE REAR TELEVISION CAMERA ASSEMBLY Click here

    OK

  4. REPLACE HARNESS AND CONNECTOR (GVIF CABLE)


    1. Replace the GVIF cable with a normally functioning one.


    NEXT

  5. CHECK PARKING ASSIST MONITOR SYSTEM (w/o Side Monitor System)


    1. Check the parking assist monitor system (w/o Side Monitor System).

      OK
      Parking assist monitor system (w/o Side Monitor System) is operated normally.

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    OK

    END (GVIF CABLE IS DEFECTIVE)