G-BOOK SYSTEM, Diagnostic DTC:B15C4

DTC Code DTC Name
B15C4 Airbag Signal Malfunction/Not Input

DESCRIPTION

If the telematics transceiver detects an error in communication between the telematics transceiver and the center airbag sensor assembly as a result of the telematics transceiver self check, this DTC will be stored.

DTC No. DTC Detection Condition Trouble Area
B15C4 Airbag signal problem

  • Airbag system

  • Harness or connector

  • Center airbag sensor assembly

  • Telematics transceiver

WIRING DIAGRAM

A01ESKZE01

INSPECTION PROCEDURE

Note

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS Click here.

Tech Tips

When replacing the telematics transceiver, perform the vehicle contract setting Click here.

PROCEDURE


  1. CHECK DTC (SRS AIRBAG SYSTEM)


    1. Clear the DTC Click here.

    2. Recheck for DTCs and check if the same trouble occurs again Click here.

      OK
      No DTC is output.

    NG

    GO TO SRS AIRBAG SYSTEM Click here

    OK

  2. CLEAR DTC


    1. Clear the DTC Click here.


    NEXT

  3. RECHECK DTC


    1. Recheck for DTCs and check if the same trouble occurs again Click here.

      OK
      No DTC is output.

    NG

    CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - CENTER AIRBAG SENSOR ASSEMBLY) Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  4. CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - CENTER AIRBAG SENSOR ASSEMBLY)


    1. Disconnect the P2 telematics transceiver connector.

    2. Disconnect the E47 center airbag sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P2-24 (GSW) - E47-24 (GSW3) Always Below 1 Ω
      P2-24 (GSW) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK TELEMATICS TRANSCEIVER


    1. A01EQREE15
      Text in Illustration
      *1

      Front view of wire harness connector

      (to Telematics Transceiver)

      Disconnect the P2 telematics transceiver connector.

    2. A01EOJ2E01

      Check the input waveform.


      1. Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telematics transceiver while the center airbag sensor assembly connectors are connected.)

        Item Condition
        Tester Connection P2-24 (GSW) - Body ground
        Tool setting 5.0 V/DIV., 20 ms/DIV.
        Vehicle condition Engine switch on (IG)

    NG

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    OK

    REPLACE TELEMATICS TRANSCEIVER Click here

  6. REPLACE CENTER AIRBAG SENSOR ASSEMBLY


    1. Replace the center airbag sensor assembly with a normal one Click here.


    NEXT

  7. CLEAR DTC


    1. Clear the DTC Click here.


    NEXT

  8. RECHECK DTC


    1. Recheck for DTCs and check if the same trouble occurs again Click here.

      OK
      No DTC is output.

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

    OK

    END (CENTER AIRBAG SENSOR ASSEMBLY IS DEFECTIVE)