NAVIGATION SYSTEM, Diagnostic DTC:B15D0

DTC Code DTC Name
B15D0 MOST Communication Malfunction

DESCRIPTION

This DTC is stored when the MOST network cannot be established after the master unit is activated.

Tech Tips


  • If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the navigation system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.

  • When the stereo component amplifier assembly stops operating and a malfunction occurs in the navigation system due to a short in a speaker circuit, this DTC will be stored.

DTC Code DTC Detection Condition Trouble Area
B15D0 MOST network cannot be established.

  • MOST line check

  • MOST communication line connector

  • MOST communication line

  • Television display assembly (w/ Rear Seat Entertainment System [for Roof])

  • Multi-display controller sub-assembly (w/ Rear Seat Entertainment System [for Seatback])

  • Stereo component amplifier assembly

  • Multi-media module receiver assembly

Tech Tips


  • For the MOST network, the multi-media module receiver assembly is the master unit.

  • Errors may occur in MOST communication between devices due to problems such as electrical noise.

WIRING DIAGRAM

A01ERKKE01

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result
      Result Proceed to
      Optional components (including associated wiring) are installed. A

      Optional components (including associated wiring) are installed.

      DTCs are not output.

      		 B

      Tech Tips


      • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

      • These DTCs may be stored when an AVC-LAN communication error occurs due to electrical noise.


    B

    CHECK MOST COMMUNICATION CONNECTORS Click here

    A

  2. CONFIRM SYMPTOMS


    1. Turn the engine switch off.

    2. Turn the engine switch on (ACC) and check if the audio system activates and if the speakers operate.

      Tech Tips


      • Choose a source such as radio so that sound can be output from the speakers.

      • If sound from the speakers is low, turn up the volume.

      Result
      Result Proceed to
      Even after the engine switch is turned on (ACC), the navigation system does not activate and sound is not output from the speakers. (w/o Rear Seat Entertainment System) A
      Even after the engine switch is turned on (ACC), the navigation system does not activate and sound is not output from the speakers. (w/ Rear Seat Entertainment System) B
      The audio system activates when the engine switch is turned on (ACC) but the sound stops being output when the amplifier output exceeds a certain level. C

      Tech Tips


      • If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the navigation system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.

      • When the stereo component amplifier assembly stops operating and a malfunction occurs in the navigation system due to a short in a speaker circuit, this DTC will be stored. In this case, check each speaker circuit and repair or replace malfunctioning parts, and then recheck for DTCs.


    B

    MOST COMMUNICATION CONNECTORS Click here

    C

    GO TO AUDIO AND VISUAL SYSTEM Click here

    A

  3. CHECK MOST COMMUNICATION CONNECTORS


    1. A01EQMQE01
      Text in Illustration
      *a Node position number for devices that use MOST communication
      *b Device name
      *c Result

      Display the "MOST Line Check" screen Click here.

    2. Check the result on the "MOST Line Check" screen.

      Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      "OK" is displayed for all items. B

      • When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.

      • The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.


    B

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) Click here

    A

  4. CONFIRM SYMPTOMS


    1. Check the MOST communication line connectors.


      1. Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems Click here.

    2. Display the "MOST Line Check" screen and check the result Click here.

      Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      The screen cannot be changed to the "MOST Line Check" screen. B

      Tech Tips

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)


    1. A01ERRHE17
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)

      Disconnect the stereo component amplifier assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F86-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher

    NG

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) Click here

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  6. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F87 multi-media module receiver assembly connector.

    2. Disconnect the F86 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F87-1 (WUO) - F86-8 (WUI) Always Below 1 Ω
      F87-1 (WUO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F87 multi-media module receiver assembly connector.

    2. Disconnect the F86 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F87-2 (MI+) - F86-5 (MO+) Always Below 1 Ω
      F87-3 (MI-) - F86-6 (MO-) Always Below 1 Ω
      F87-4 (SLDI) - F86-7 (SLDO) Always Below 1 Ω
      F87-5 (MO+) - F86-2 (MI+) Always Below 1 Ω
      F87-6 (MO-)- F86-3 (MI-) Always Below 1 Ω
      F87-7 (SLDO) - F86-4 (SLDI) Always Below 1 Ω
      F87-2 (MI+) - Body ground Always 10 kΩ or higher
      F87-3 (MI-) - Body ground Always 10 kΩ or higher
      F87-4 (SLDI) - Body ground Always 10 kΩ or higher
      F87-5 (MO+) - Body ground Always 10 kΩ or higher
      F87-6 (MO-) - Body ground Always 10 kΩ or higher
      F87-7 (SLDO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY


    1. Replace the stereo component amplifier assembly with a new or normally functioning one Click here.


    NEXT

  9. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  10. CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again Click here.

      OK
      No DTCs are output

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

    END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

  11. MOST COMMUNICATION CONNECTORS


    1. A01EOPAE01
      Text in Illustration
      *a Node position number for devices that use MOST communication
      *b Device name
      *c Result

      Display the "MOST Line Check" screen Click here.

    2. Check the result on the "MOST Line Check" screen.

      Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      "NCON" is displayed for "RSE". B
      "OK" is displayed for all items. C

      • When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.

      • The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.


    B

    CONFIRM SYMPTOMS Click here

    C

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) Click here

    A

  12. CONFIRM SYMPTOMS


    1. Check the MOST communication line connectors.


      1. Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems Click here.

    2. Display the "MOST Line Check" screen and check the result Click here.

      Result
      Result Proceed to
      "NCON" is displayed for "AMP". A
      The screen cannot be changed to the "MOST Line Check" screen. B

      Tech Tips

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  13. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE)


    1. A01ERRHE17
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)

      Disconnect the stereo component amplifier assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      F86-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher

    NG

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) Click here

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  14. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F87 multi-media module receiver assembly connector.

    2. Disconnect the F86 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F87-1 (WUO) - F86-8 (WUI) Always Below 1 Ω
      F87-1 (WUO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

  15. CONFIRM SYMPTOMS


    1. Check the MOST communication line connectors.


      1. Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems Click here.

    2. Display the "MOST Line Check" screen and check the result Click here.

      Result
      Result Proceed to
      "NCON" is displayed for "RSE" (for Roof). A
      "NCON" is displayed for "RSE" (for Seatback). B
      The screen cannot be changed to the "MOST Line Check" screen. C

      Tech Tips

      When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.


    B

    CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY Wake Up LINE) Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  16. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY Wake Up LINE)


    1. A01ERRHE18
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Television Display Assembly)

      Disconnect the television display assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L59-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher

    NG

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY) Click here

    OK

    REPLACE TELEVISION DISPLAY ASSEMBLY Click here

  17. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)


    1. Disconnect the F86 stereo component amplifier assembly connector.

    2. Disconnect the L59 television display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F86-1 (WUO) - L59-8 (WUI) Always Below 1 Ω
      F86-1 (WUO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  18. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY Wake Up LINE)


    1. A01ERRHE19
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Multi-display Controller Sub-assembly)

      Disconnect the multi-display controller sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L60-8 (WUI) - Body ground Engine switch on (ACC) 4.5 V or higher

    NG

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY) Click here

    OK

    REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY Click here

  19. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY)


    1. Disconnect the F86 stereo component amplifier assembly connector.

    2. Disconnect the L60 multi-display controller sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F86-1 (WUO) - L60-8 (WUI) Always Below 1 Ω
      F86-1 (WUO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  20. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the F87 multi-media module receiver assembly connector.

    2. Disconnect the F86 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F87-5 (MO+) - F86-2 (MI+) Always Below 1 Ω
      F87-6 (MO-) - F86-3 (MI-) Always Below 1 Ω
      F87-7 (SLDO) - F86-4 (SLDI) Always Below 1 Ω
      F87-5 (MO+) - Body ground Always 10 kΩ or higher
      F87-6 (MO-) - Body ground Always 10 kΩ or higher
      F87-7 (SLDO) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (for Roof) A
      (OK (for Seatback) B
      NG C

    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY) Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  21. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)


    1. Disconnect the F86 stereo component amplifier assembly connector.

    2. Disconnect the L59 television display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F86-5 (MO+) - L59-2 (MI+) Always Below 1 Ω
      F86-6 (MO-) - L59-3 (MI-) Always Below 1 Ω
      F86-7 (SLDO) - L59-4 (SLDI) Always Below 1 Ω
      F86-5 (MO+) - Body ground Always 10 kΩ or higher
      F86-6 (MO-) - Body ground Always 10 kΩ or higher
      F86-7 (SLDO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  22. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)


    1. Disconnect the F87 multi-media module receiver assembly connector.

    2. Disconnect the L59 television display assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F87-2 (MI+) - L59-5 (MO+) Always Below 1 Ω
      F87-3 (MI-) - L59-6 (MO-) Always Below 1 Ω
      F87-4 (SLDI) - L59-7 (SLDO) Always Below 1 Ω
      F87-2 (MI+) - Body ground Always 10 kΩ or higher
      F87-3 (MI-) - Body ground Always 10 kΩ or higher
      F87-4 (SLDI) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  23. REPLACE TELEVISION DISPLAY ASSEMBLY


    1. Replace the television display assembly with a new or normally functioning one Click here.


    NEXT

  24. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  25. CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again Click here.

      OK
      No DTCs are output.

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

    END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)

  26. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY)


    1. Disconnect the F86 stereo component amplifier assembly connector.

    2. Disconnect the L60 multi-display controller sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F86-5 (MO+) - L60-2 (MI+) Always Below 1 Ω
      F86-6 (MO-) - L60-3 (MI-) Always Below 1 Ω
      F86-7 (SLDO) - L60-4 (SLDI) Always Below 1 Ω
      F86-5 (MO+) - Body ground Always 10 kΩ or higher
      F86-6 (MO-) - Body ground Always 10 kΩ or higher
      F86-7 (SLDO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  27. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY)


    1. Disconnect the F87 multi-media module receiver assembly connector.

    2. Disconnect the L60 multi-display controller sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F87-2 (MI+) - L60-5 (MO+) Always Below 1 Ω
      F87-3 (MI-) - L60-6 (MO-) Always Below 1 Ω
      F87-4 (SLDI) - L60-7 (SLDO) Always Below 1 Ω
      F87-2 (MI+) - Body ground Always 10 kΩ or higher
      F87-3 (MI-) - Body ground Always 10 kΩ or higher
      F87-4 (SLDI) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  28. REPLACE MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY


    1. Replace the multi-display controller sub-assembly with a new or normally functioning one Click here.


    NEXT

  29. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  30. CHECK DTC


    1. Recheck for DTCs and check if the same DTC is output again Click here.

      OK
      No DTCs are output.

    NG

    USE SIMULATION METHOD TO CHECK Click here

    OK

    END (MULTI-DISPLAY CONTROLLER SUB-ASSEMBLY IS DEFECTIVE)