STEREO COMPONENT AMPLIFIER INSTALLATION

INSTALL NO. 2 AMPLIFIER BRACKET
1. Set the aligning protrusions of the bracket, labeled A, into the holes of the amplifier.
2. Install the bracket with the 2 screws labeled B.
  
  Torque:
  
  3.0 N*m { 30 kgf*cm, 26 in.*lbf }
INSTALL NO. 1 AMPLIFIER BRACKET
1. Set the aligning protrusions of the bracket, labeled A, into the holes of the amplifier.
2. Install the bracket with the 2 screws labeled B.
  
  Torque:
  
  3.0 N*m { 30 kgf*cm, 26 in.*lbf }
INSTALL AMPLIFIER COVER (for 9 Speakers)
1. Attach the 3 clips to install the cover.
INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET
1. Install the amplifier with the 3 bolts.
  
  Torque:
  
  7.5 N*m { 76 kgf*cm, 66 in.*lbf }
2. for 19 Speakers:
  
  Connect the 6 connectors.
3. for 9 Speakers:
  
  Connect the 3 connectors.
INSTALL FRONT FLOOR CARPET ASSEMBLY
1. Open the tail gate and back door, insert the carpet into the cabin from the rear, and install it to the floor.
2. Attach the 2 clips and 8 claws.
INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)
1. Install the rear console box Click here.
INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)
1. Install the cooling box Click here.
INSTALL REAR NO. 2 SEAT PROTECTOR
1. Attach the 4 clips and claw to install the protector.
  
  Tech Tips
  
  Use the same procedures to install the protector on the other side.
INSTALL REAR NO. 1 SEAT PROTECTOR
1. Attach the 4 clips and claw to install the protector.
  
  Tech Tips
  
  Use the same procedures to install the protector on the other side.
INSTALL REAR AIR DUCT GUIDE
Tech Tips

Use the same procedures for both sides.
1. Attach the claw to install the guide.
2. Install the screw.
INSTALL AIR DUCT PLUG
1. Attach the 2 claws to install the plug.
  
  Tech Tips
  
  Use the same procedures for both sides.
INSTALL AIR HEATER GUIDE
1. Install the guide with the 2 screws.
  
  Tech Tips
  
  Use the same procedures for both sides.
INSTALL NO. 2 AIR DUCT PLUG
1. Attach the 4 claws to install the 2 plugs.
  
  Tech Tips
  
  Use the same procedures for both sides.
INSTALL REAR DOOR SCUFF PLATE RH

Tech Tips

Use the same procedures described for the LH side.
INSTALL REAR DOOR SCUFF PLATE LH
1. w/o Illumination Type Front Door Scuff Plate:
  1. Attach the 3 claws and 4 clips to install the scuff plate.
  2. Install the screw.
2. w/ Illumination Type Front Door Scuff Plate:
  1. Attach the 3 claws and 4 clips to install the scuff plate.
  2. Install the screw.
INSTALL REAR STEP COVER
Tech Tips

Use the same procedure to install the step cover on the other side.
1. w/o Illumination Type Front Door Scuff Plate:
  
  Attach the 2 claws to install the step cover.
2. w/ Illumination Type Front Door Scuff Plate:
  
  Attach the 4 claws to install the step cover.
INSTALL COWL SIDE TRIM BOARD RH
1. Attach the 2 clips to install the trim board.
2. Install the cap nut.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
1. Connect the connector.
2. Attach the 4 claws to install the under cover.
INSTALL COWL SIDE TRIM BOARD LH
1. Attach the 2 clips to install the trim board.
2. Install the cap nut.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
1. Connect the connectors.
2. Attach the 3 claws to install the under cover.
3. Install the 2 screws.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedures described for the LH side.
INSTALL FRONT DOOR SCUFF PLATE LH
1. w/o Illumination:
  1. Attach the 7 claws and 4 clips to install the scuff plate.
2. w/ Illumination:
  1. Connect the connector.
  2. Attach the 7 claws and 4 clips to install the scuff plate.
INSTALL INSTRUMENT SIDE PANEL RH
1. w/o Airbag Cut Off Switch:
  1. Attach the 6 claws to install the side panel.
2. w/ Airbag Cut Off Switch:
  1. Connect the connector.
  2. Attach the 6 claws to install the side panel.
INSTALL INSTRUMENT SIDE PANEL LH
1. Attach the 6 claws to install the side panel.
INSTALL REAR NO. 1 SEAT ASSEMBLY RH
1. Temporarily install the seat assembly with the 4 bolts.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Tighten the bolts in the order shown in the illustration.
  
  Torque:
  
  37 N*m { 377 kgf*cm, 27 ft.*lbf }
3. Connect the connector.
4. w/ Seat Heater System:
  
  Connect the connector.
INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER
1. Attach the 2 clips and 2 claws to install the cover.
INSTALL REAR NO. 1 SEAT CUSHION HINGE COVER
1. Attach the 2 clips and 2 claws to install the cover.
INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER
1. Return the seat to the upright position.
2. Attach the 7 claws to install the cover.
INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER
1. Attach the 6 claws to install the cover.
INSTALL REAR NO. 1 SEAT ASSEMBLY LH
1. Temporarily install the seat assembly with the 4 bolts.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Tighten the bolts in the order shown in the illustration.
  
  Torque:
  
  37 N*m { 377 kgf*cm, 27 ft.*lbf }
3. Connect the connector.
4. w/ Seat Heater System:
  
  Connect the connector.
INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER
1. Attach the 2 clips and 2 claws to install the cover.
INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER
1. Attach the 2 clips and 2 claws to install the cover.
INSTALL REAR NO. 5 SEAT CUSHION HINGE COVER
1. Return the seat to the upright position.
2. Attach the 7 claws to install the cover.
INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER
1. Attach the 6 claws to install the cover.
INSTALL FRONT SEAT ASSEMBLY RH
1. Install the front seat assembly RH Click here.
INSTALL FRONT SEAT ASSEMBLY LH
1. Install the front seat assembly LH Click here.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL ENGINE ROOM SIDE COVER LH
1. Install the engine room side cover LH with the 7 clips.
CHECK SRS WARNING LIGHT
1. Check the SRS warning light Click here.