STEERING COLUMN ASSEMBLY INSTALLATION


  1. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT


    1. A01ER9ZE01

      Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

      Note

      Be careful not to damage the dust cover.

  2. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    1. A01ENQ4

      Install the steering column hole cover with the 4 bolts and nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      Tech Tips

      Install the steering intermediate shaft assembly from the inside of the vehicle.

    2. Install the clamp to the steering column hole cover.

  3. INSTALL STEERING ACTUATOR ASSEMBLY


    1. Make sure that the power steering link assembly is centered.

    2. A01EOHDE01

      Install the steering actuator assembly.


      1. If installing a new steering actuator assembly:

        Install the steering actuator assembly with the white line on the upper surface of the spiral case facing down.

        Note

        Do not pull out the center lock pin.

      2. A01EQLBE01

        If reinstalling the removed steering actuator assembly:


        1. Slowly turn the spiral case clockwise until it locks.

        2. Turn the spiral case two turns counterclockwise from the lock position.

        3. Align the slit of the sliding yoke with the alignment mark (▲).

        4. Install the steering actuator assembly with the white line on the upper surface of the spiral case facing down.

    3. A01ESH3E01

      Align the matchmarks on the No. 2 steering intermediate shaft and steering actuator.

      Tech Tips

      Install the steering actuator from the inside of the vehicle.

      Note


      • Do not fold back the boot part of the steering hole cover or turn it excessively. If it is turned excessively, return it to its original position.

      • Do not turn the actuator body and the spiral case.

    4. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }
    5. A01EP6M

      Using needle nose pliers, lock the clamp to the steering column hole cover to install it.

      Note

      Be careful when performing the operation as the clamp may not lock if the claws of the clamp are deformed.

    6. A01EOMF

      Move the lock in the direction of the arrow and connect the steering actuator connector.

      Tech Tips

      When a new actuator is installed, remove the center lock pin.

    7. Connect the connector.

  4. INSTALL STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)


    1. A01EQE0

      Install the steering column with the 4 nuts.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

  5. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

    A01EQW3

    1. Attach the 2 claws to install the duct.

    2. Install the clip.

  6. CONNECT WIRE HARNESS PROTECTOR AND WIRE HARNESS


    1. A01ESK1

      Attach the 3 claws to connect the wiring harness protector and wire harness.

  7. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. A01ENCE

      Connect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the driver side knee airbag with the 5 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  8. INSTALL INSTRUMENT PANEL BOX ASSEMBLY


    1. A01ENPQ

      Connect the connectors.

    2. Attach the 5 claws to install the box.

  9. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A01EN2R

    1. Connect the connectors.

    2. Attach the 2 claws to install the sensor.

    3. A01EQEE

      Attach the 2 claws to connect the 2 control cables.

    4. A01EQBC

      Attach the 16 claws to install the finish panel.

    5. A01EOJD

      Install the 2 bolts.

    6. A01ENQK

      Attach the 2 claws to close the hole cover.

  10. INSTALL COWL SIDE TRIM BOARD LH


    1. A01EQ1Q

      Attach the 2 clips to install the trim board.

    2. Install the cap nut.

  11. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01EQBL

      Connect the connectors.

    2. Attach the 3 claws to install the under cover.

    3. Install the 2 screws.

  12. INSTALL FRONT DOOR SCUFF PLATE LH

    A01EQ14

    1. w/o Illumination:


      1. Attach the 7 claws and 4 clips to install the scuff plate.

    2. A01EOWQ

      w/ Illumination:


      1. Connect the connector.

      2. Attach the 7 claws and 4 clips to install the scuff plate.

  13. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01ER8Q

      Attach the 5 claws to install the register.

  14. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01ERR3

      Attach the 4 claws to install the register.

  15. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01EQ6K

      Connect the connectors.

    2. Attach the 4 claws to install the finish panel.

  16. INSTALL NO. 1 SWITCH HOLE BASE


    1. A01EQ09

      Connect the connectors.

    2. Attach the 5 claws to install the switch hole base.

  17. INSTALL INSTRUMENT SIDE PANEL LH


    1. A01EQQM

      Attach the 6 claws to install the side panel.

  18. INSTALL INNER NO. 1 INSTRUMENT PANEL BRACKET COVER LH


    1. A01ER40

      Attach the clip to install the cover.

    2. Install the clip.

  19. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


    1. A01EP7O

      Attach the 9 claws to install the panel pad.

  20. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. A01ERQSE01

      Using pliers, grip the claws of the clamp and install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

    2. A01EN6M

      Connect the 5 connectors to the turn signal switch with spiral cable.

  21. INSTALL TILT AND TELESCOPIC SWITCH


    1. Attach the claw to install the switch.

    2. Connect the switch connector.

  22. INSTALL UPPER STEERING COLUMN COVER


    1. A01ERUT

      Attach the claw to install the upper steering column cover.

    2. Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

  23. INSTALL LOWER STEERING COLUMN COVER


    1. A01ERJD

      Attach the 2 claws to install the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    2. Install the 3 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  24. ADJUST SPIRAL CABLE


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the battery negative (-) terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    3. A01ENPK

      Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

      CAUTION:

      Do not turn the spiral cable with steering sensor by the airbag wire harness.

    4. A01EOGOE01

      Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

      CAUTION:

      Do not turn the spiral cable with spiral sensor by the airbag wire harness.

      Tech Tips

      The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.

  25. INSTALL STEERING WHEEL ASSEMBLY

    A01EQVCE01

    1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  26. INSTALL STEERING PAD


    1. A01EQYD

      Support the steering pad with one hand.

    2. Connect the 2 connectors to the steering pad.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    3. Connect the horn connector.

    4. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel.

    5. Using a T30 "TORX" socket wrench, tighten the 2 screws.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  27. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A01ES8Q

      Attach the 2 claws to install the cover.

  28. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A01EOLU

      Attach the 2 claws to install the cover.

  29. CHECK FRONT WHEELS FACING STRAIGHT AHEAD

  30. INSTALL FRONT WHEELS

  31. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    Reset the Autoaway/Return function setting to the previous condition by changing the customize parameter Click here.

  32. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.

  33. PERFORM VARIABLE GEAR RATIO STEERING SYSTEM CALIBRATION


    1. Perform variable gear ratio steering system calibration Click here.