STEERING CONTROL ECU (for LHD) INSTALLATION


  1. INSTALL STEERING CONTROL ECU

    A01ERNIE01

    1. Install the ECU to the junction block with the bolt and nut.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  2. INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK

    A01EQJ0E01

    1. Front side:


      1. Connect the 5 connectors.

    2. Rear side:


      1. Install the ECU with junction block with the 2 bolt and nuts.

        Torque:
        8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      2. Attach the 2 clamps.

      3. Connect the 7 connectors.

  3. INSTALL INSTRUMENT PANEL BOX ASSEMBLY


    1. A01ENPQ

      Connect the connectors.

    2. Attach the 5 claws to install the box.

  4. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. A01ENCE

      Connect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the driver side knee airbag with the 5 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  5. INSTALL NO. 1 SWITCH HOLE BASE


    1. A01EQ09

      Connect the connectors.

    2. Attach the 5 claws to install the switch hole base.

  6. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A01EN2R

    1. Connect the connectors.

    2. Attach the 2 claws to install the sensor.

    3. A01EQEE

      Attach the 2 claws to connect the 2 control cables.

    4. A01EQBC

      Attach the 16 claws to install the finish panel.

    5. A01EOJD

      Install the 2 bolts.

    6. A01ENQK

      Attach the 2 claws to close the hole cover.

  7. INSTALL COWL SIDE TRIM BOARD LH


    1. A01EQ1Q

      Attach the 2 clips to install the trim board.

    2. Install the cap nut.

  8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01EQBL

      Connect the connectors.

    2. Attach the 3 claws to install the under cover.

    3. Install the 2 screws.

  9. INSTALL FRONT DOOR SCUFF PLATE LH

    A01EQ14

    1. w/o Illumination:


      1. Attach the 7 claws and 4 clips to install the scuff plate.

    2. A01EOWQ

      w/ Illumination:


      1. Connect the connector.

      2. Attach the 7 claws and 4 clips to install the scuff plate.

  10. INSTALL INSTRUMENT SIDE PANEL LH


    1. A01EQQM

      Attach the 6 claws to install the side panel.

  11. INSTALL INNER NO. 1 INSTRUMENT PANEL BRACKET COVER LH


    1. A01ER40

      Attach the clip to install the cover.

    2. Install the clip.

  12. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


    1. A01EO0Q

      Connect the connector.

    2. Attach the 8 claws to install the panel pad.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.