VARIABLE GEAR RATIO STEERING SYSTEM, Diagnostic DTC:C15A3/63, C15C5/69

DTC Code DTC Name
C15A3/63 Actuator Malfunction
C15C5/69 Motor Revolution Angle Signal (Test Mode DTC)

DESCRIPTION

The steering actuator drives the internal motor using the current output from the steering control ECU to change the relative angle between the tire angle and steering wheel angle.

The rotation angle sensor in the steering actuator detects the motor rotation angle and outputs this information to the steering control ECU.

If the steering control ECU detects a malfunction in the rotation angle sensor circuit, it will store DTC C15A3/63.

DTC Code DTC Detection Condition Trouble Area
C15A3/63 The steering control ECU detects a malfunction in the rotation angle sensor circuit.

  • Harness or connector

  • Steering actuator

  • Steering control ECU
C15C5/69 A steering signal indicating a motor rotation angle of 36° or more (to the left or right) is input after entering test mode.*

  • Harness or connector

  • Steering actuator

  • Steering control ECU

Tech Tips

*: A tire angle of 36° and a motor rotation angle of 36° correspond to the steering wheel angle. The amount of change in tire angle and motor rotation angle is from when the mode is changed to test mode.

WIRING DIAGRAM

A01ENTIE07

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (STEERING CONTROL ECU - STEERING ACTUATOR)

    A01EP7DE03

    1. Disconnect the E84 steering control ECU connector.

    2. Disconnect the E85 steering actuator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E84-4 (S1) - E85-2 (S1+) Always Below 1 Ω
      E84-6 (RV) - E85-1 (RV+)
      E84-14 (S2) - E85-9 (S2+)
      E84-15 (RG) - E85-10 (RG+)
      E84-4 (S1) - E84-6 (RV) Always 10 kΩ or higher
      E84-4 (S1) - E84-14 (S2)
      E84-4 (S1) - E84-15 (RG)
      E84-6 (RV) - E84-14 (S2)
      E84-6 (RV) - E84-15 (RG)
      E84-14 (S2) - E84-15 (RG)
      E84-4 (S1) - Body ground
      E84-6 (RV) - Body ground
      E84-14 (S2) - Body ground
      E84-15 (RG) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. CHECK STEERING ACTUATOR


    1. A01EN8FE04

      Disconnect the E84 steering control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      The resistance must be measured with the steering actuator connector connected.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E84-4 (S1) - E84-6 (RV) Always Below 200 Ω
      E84-4 (S1) - E84-14 (S2)
      E84-4 (S1) - E84-15 (RG)
      E84-6 (RV) - E84-14 (S2)
      E84-6 (RV) - E84-15 (RG)
      E84-14 (S2) - E84-15 (RG)
      E84-4 (S1) - Body ground Always 10 kΩ or higher
      E84-6 (RV) - Body ground
      E84-14 (S2) - Body ground
      E84-15 (RG) - Body ground
      Result

      Result

      		 Proceed to
      NG A
      OK (for LHD) B
      OK (for RHD) C

    B

    REPLACE STEERING CONTROL ECU Click here

    C

    REPLACE STEERING CONTROL ECU Click here

    A

    REPLACE STEERING ACTUATOR ASSEMBLY Click here