STEERING ANGLE SENSOR INSTALLATION


  1. INSTALL STEERING ANGLE SENSOR


    1. A01EQTEE02

      Align the installation holes on the steering angle sensor with the pins on the spiral cable.

    2. Attach the 6 claws to install the steering angle sensor to the spiral cable.

  2. INSTALL SPIRAL CABLE SUB-ASSEMBLY


    1. A01ESGKE03

      Align the pins on the spiral cable with the installation holes on the steering sensor.

    2. Attach the 6 claws and install the spiral cable to the steering sensor.

    3. Check that the front wheels are facing straight ahead.

    4. Set the turn signal switch to the neutral position.

      CAUTION:

      If it is not in the neutral position, the pin of the turn signal switch may be snapped.

    5. A01ENU2

      Attach the 3 claws to install the spiral cable with steering sensor.

      CAUTION:

      When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel assembly.

    6. Connect the connectors to the spiral cable with steering sensor.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL UPPER STEERING COLUMN COVER


    1. A01ERUT

      Attach the claw to install the upper steering column cover.

    2. Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

  4. INSTALL LOWER STEERING COLUMN COVER


    1. A01ERJD

      Attach the 2 claws to install the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    2. Install the 3 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  5. ADJUST SPIRAL CABLE


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the battery negative (-) terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    3. A01ENPK

      Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

      CAUTION:

      Do not turn the spiral cable with steering sensor by the airbag wire harness.

    4. A01EOGOE01

      Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

      CAUTION:

      Do not turn the spiral cable with spiral sensor by the airbag wire harness.

      Tech Tips

      The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.

  6. INSTALL STEERING WHEEL ASSEMBLY

    A01EQVCE01

    1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  7. INSTALL STEERING PAD


    1. A01EQYD

      Support the steering pad with one hand.

    2. Connect the 2 connectors to the steering pad.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    3. Connect the horn connector.

    4. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel.

    5. Using a T30 "TORX" socket wrench, tighten the 2 screws.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  8. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A01ES8Q

      Attach the 2 claws to install the cover.

  9. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A01EOLU

      Attach the 2 claws to install the cover.

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Reset the Autoaway/Return function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.