FRONT SPEED SENSOR INSTALLATION


  1. INSTALL FRONT SPEED SENSOR LH


    1. A01ES55

      Install the speed sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.

      • While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.

      • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

      • Make sure there is no foreign matter attached to the speed sensor rotor.

  2. INSTALL FRONT SKID CONTROL SENSOR WIRE LH


    1. A01EQWNE01

      Connect the 2 connectors.

    2. Install the harness clamp with the bolt.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    3. A01ERSZ

      Install the 2 harness clamps with the 2 bolts.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamps, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    4. A01ER3D

      Install the harness clamp with the nut.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    5. A01ES95E01

      Install the harness clamp with the bolt.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Install the bracket so that the rotation stopper touches the knuckle.

    6. Connect the speed sensor connector.

      Note

      Securely connect the connector.

  3. INSTALL FRONT SPEED SENSOR RH


    1. A01EQAS

      Install the speed sensor with the bolt.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note


      • Make sure there are no pieces of iron or other foreign matter attached to the sensor tip part.

      • While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip part.

      • After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.

      • Make sure there is no foreign matter attached to the speed sensor rotor.

  4. INSTALL FRONT SKID CONTROL SENSOR WIRE RH


    1. A01ESIHE01

      Install the skid control sensor clamp with the bolt (labeled A).

      Torque:
      for bolt A
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    2. Attach the connector to the skid control sensor clamp and then connect the connector.

    3. Install the 2 harness clamps with the 2 bolts.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamps, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    4. A01EO5K

      Install the harness clamp with the bolt.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

    5. Connect the connector.

    6. A01ES1U

      Install the harness clamp with the nut.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note


      • When installing the clamp, do not twist the wire harness.

      • Make sure the clamp rotation stopper touches the installation position.

    7. A01EQIGE01

      Install the harness clamp with the bolt.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Install the bracket so that the rotation stopper touches the knuckle.

    8. Connect the speed sensor connector.

      Note

      Securely connect the connector.

  5. INSTALL FRONT WHEEL

    Torque:
    131 N*m  { 1336 kgf*cm, 97 ft.*lbf }

  6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. CHECK SPEED SENSOR SIGNAL

    Click here