LIGHTING SYSTEM Interior Foot Light does not Illuminate

WIRING DIAGRAM

A01ERZDE01

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING INTELLIGENT TESTER (DOOR COURTESY SWITCH)


    1. Using the intelligent tester, read the Data List.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      D Door Courtesy SW Front door courtesy light switch LH signal/ON or OFF

      ON: Front Door LH open

      OFF: Front Door LH closed

      		 -
      P Door Courtesy SW Front door courtesy light switch RH signal/ON or OFF

      ON: Front Door RH open

      OFF: Front Door RH closed

      		 -
      RL Door Courtesy SW Rear door courtesy light switch LH signal/ON or OFF

      ON: Rear Door LH open

      OFF: Rear Door LH closed

      		 -
      RR Door Courtesy SW Rear door courtesy light switch RH signal/ON or OFF

      ON: Rear Door RH open

      OFF: Rear Door RH closed

      		 -
      OK
      On the intelligent tester screen, each item changes between ON and OFF according to above chart.
      Result
      Result Proceed to
      OK A
      NG (D Door Courtesy SW) B
      NG (P Door Courtesy SW) C
      NG (RL Door Courtesy SW) D
      NG (RR Door Courtesy SW) E

    B

    INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH Click here

    C

    INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH Click here

    D

    INSPECT REAR DOOR COURTESY LIGHT SWITCH LH Click here

    E

    INSPECT REAR DOOR COURTESY LIGHT SWITCH RH Click here

    A

  2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT INTERIOR FOOT LIGHT)


    1. Using the intelligent tester, perform the Active Test.

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Step Light Operation Interior foot light illumination light operation OFF/ON -
      OK
      Front interior foot light condition can be switched by Active Test.

    NG

    CONFIRM LIGHT POSITION Click here

    OK

    REPLACE MAIN BODY ECU

  3. CONFIRM LIGHT POSITION


    1. Check the malfunctioning interior illumination light.

      Result
      Result Proceed to
      Front interior foot light LH A
      Front interior foot light RH B
      Rear interior foot light LH C
      Rear interior foot light RH D
      All lights do not illuminate E

    B

    CHECK HARNESS AND CONNECTOR (FRONT INTERIOR FOOT LIGHT RH - BATTERY) Click here

    C

    CHECK HARNESS AND CONNECTOR (REAR INTERIOR FOOT LIGHT LH - BATTERY) Click here

    D

    CHECK HARNESS AND CONNECTOR (REAR INTERIOR FOOT LIGHT RH - BATTERY) Click here

    E

    REPLACE MAIN BODY ECU

    A

  4. CHECK HARNESS AND CONNECTOR (FRONT INTERIOR FOOT LIGHT LH - BATTERY)

    A01EQZGE13

    1. Disconnect the E81 light connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E81-2 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT LH (FRONT INTERIOR FOOT LIGHT LH)

    A01ERQLE10

    1. Remove the front interior foot light LH Click here.

    2. Apply battery voltage to the front interior foot light and check the light condition.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 2

      Battery negative (-) → Terminal 1

      		 Interior illumination light comes on

    NG

    REPLACE NO. 1 INTERIOR ILLUMINATION LIGHT LH (FRONT INTERIOR FOOT LIGHT LH) Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT INTERIOR FOOT LIGHT LH)

    A01EOSME05

    1. Disconnect the E3 ECU connector.

    2. Disconnect the E81 light connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E3-11 (FSPT) - E81-1 Always Below 1 Ω
      E81-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU

  7. CHECK HARNESS AND CONNECTOR (FRONT INTERIOR FOOT LIGHT RH - BATTERY)

    A01EQZGE14

    1. Disconnect the E88 light connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E88-2 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT RH (FRONT INTERIOR FOOT RH)

    A01ERQLE11

    1. Remove the front interior foot light RH Click here.

    2. Apply battery voltage to the front interior foot light and check the light condition.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 2

      Battery negative (-) → Terminal 1

      		 Interior illumination light comes on

    NG

    REPLACE NO. 1 INTERIOR ILLUMINATION LIGHT RH (FRONT INTERIOR FOOT LIGHT RH) Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT INTERIOR FOOT LIGHT RH)

    A01EOSME09

    1. Disconnect the E3 ECU connector.

    2. Disconnect the E88 light connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E3-11 (FSPT) - E88-1 Always Below 1 Ω
      E88-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU

  10. CHECK HARNESS AND CONNECTOR (REAR INTERIOR FOOT LIGHT LH - BATTERY)

    A01EQZGE18

    1. Disconnect the c32 light connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      c32-2 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. INSPECT INTERIOR ILLUMINATION LIGHT LH (REAR INTERIOR FOOT LIGHT LH)

    A01ESDXE14

    1. Remove the rear interior foot light LH Click here.

    2. Apply battery voltage to the rear interior foot light and check the light condition.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 2

      Battery negative (-) → Terminal 1

      		 Interior illumination light comes on

    NG

    REPLACE INTERIOR ILLUMINATION LIGHT LH (REAR INTERIOR FOOT LIGHT LH) Click here

    OK

  12. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR INTERIOR ILLUMINATION LIGHT LH)

    A01EOSME11

    1. Disconnect the E3 ECU connector.

    2. Disconnect the c32 light connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E3-11 (FSPT) - c32-1 Always Below 1 Ω
      c32-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU

  13. CHECK HARNESS AND CONNECTOR (REAR INTERIOR FOOT LIGHT RH - BATTERY)

    A01EQZGE19

    1. Remove the c44 ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      c44-2 - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. INSPECT INTERIOR ILLUMINATION LIGHT RH (REAR INTERIOR FOOT LIGHT RH)

    A01ESDXE21

    1. Remove the rear interior foot light RH Click here.

    2. Apply battery voltage to the rear interior foot light and check the light condition.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → Terminal 2

      Battery negative (-) → Terminal 1

      		 Interior illumination light comes on

    NG

    REPLACE INTERIOR ILLUMINATION LIGHT RH (REAR INTERIOR FOOT LIGHT RH) Click here

    OK

  15. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR INTERIOR FOOT LIGHT RH)

    A01EOSME12

    1. Disconnect the E3 ECU connector.

    2. Disconnect the c44 light connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E3-11 (FSPT) - c44-1 Always Below 1 Ω
      c44-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU

  16. INSPECT FRONT DOOR COURTESY LIGHT SWITCH LH


    1. A01EQM3E01

      Remove the front door courtesy light switch LH Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - Body ground Not pushed Below 1 Ω
      Pushed 10 kΩ or higher

    NG

    REPLACE FRONT DOOR COURTESY LIGHT SWITCH LH Click here

    OK

  17. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU AND BODY GROUND)


    1. A01ESEDE01

      Disconnect the K2 switch connector.

    2. Disconnect the E1 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      K2-1 - E1-24 (DCTY) Always Below 1 Ω
      K2-1 - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      K2-1 - E1-21 (PCTY) Always Below 1 Ω
      K2-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU

  18. INSPECT FRONT DOOR COURTESY LIGHT SWITCH RH


    1. A01EQM3E02

      Remove the front door courtesy light switch RH Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - Body ground Not pushed Below 1 Ω
      Pushed 10 kΩ or higher

    NG

    REPLACE FRONT DOOR COURTESY LIGHT SWITCH RH Click here

    OK

  19. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU AND BODY GROUND)


    1. A01EP1IE01

      Disconnect the L1 switch connector.

    2. Disconnect the E2 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      L1-1 - E2-21 (PCTY) Always Below 1 Ω
      L1-1 - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      L1-1 - E2-24 (DCTY) Always Below 1 Ω
      L1-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU

  20. INSPECT REAR DOOR COURTESY LIGHT SWITCH LH


    1. A01EQM3E03

      Remove the rear door courtesy light switch LH Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - Body ground Not pushed Below 1 Ω
      Pushed 10 kΩ or higher

    NG

    REPLACE REAR DOOR COURTESY LIGHT SWITCH LH Click here

    OK

  21. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH LH - MAIN BODY ECU AND BODY GROUND)


    1. A01EOITE02

      Disconnect the K3 switch connector.

    2. Disconnect the 2C ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K3-1 - 2C-2 (LCTY) Always Below 1 Ω
      K3-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU

  22. INSPECT REAR DOOR COURTESY LIGHT SWITCH RH


    1. A01EQM3E04

      Remove the rear door courtesy light switch RH Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - Body ground Not pushed Below 1 Ω
      Pushed 10 kΩ or higher

    NG

    REPLACE REAR DOOR COURTESY LIGHT SWITCH RH Click here

    OK

  23. CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH RH - MAIN BODY ECU AND BODY GROUND)


    1. A01EMVVE02

      Disconnect the L2 switch connector.

    2. Disconnect the E2 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L2-1 - E2-7 (RCTY) Always Below 1 Ω
      L2-1 - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU