LIGHTING SYSTEM CUSTOMIZE PARAMETERS


  1. CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER (REFERENCE)

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Customize Setting.

    5. Select the setting by referring to the table below.

      Illuminated Entry
      Display Default Content Setting
      I/L when ACC OFF ON Function to illuminate the interior light when the engine switch is turned from on (IG) or on (ACC) to off. ON/OFF
      Lighting Time 15s

      Function to change the lighting time after closing the door.

      (It will quickly fade out in the case of turning the engine switch on (IG)).

      		 7.5s/15s/30s
      Light Control ON Function to illuminate the door inside handle illumination light when the engine switch is on (IG) and the shift lever is not in P. ON/OFF
      I/L ON W/Door Key Unlock ON Function to illuminate the interior light, etc. when the door is unlocked with a transmitter, door key or door lock control switch. ON/OFF
      Mirr-Foot-Lgt Approached ON Function to illuminate the door mirror foot light and step light when the transmitter enters the key ID detection area. ON/OFF
      Mirr-Foot-Lgt Unlocked ON Function to illuminate the door mirror foot light and step light when unlocking the doors with the transmitter. ON/OFF
      Mirr-Foot-Lgt w/Master SW ON Function to illuminate the door mirror foot light and step light when unlocking the doors with the door lock master switch. ON/OFF
      Mirror Foot Light Time 15s Door mirror foot light and step light illumination duration. 0s/7.5s/15s/30s
      Room Light when Aprchd ON Function to illuminate the dome light when the transmitter enters the key ID detection area. ON/OFF
      Inside Foot Light ON Interior foot light illumination. ON/OFF
      Center Console Spot Light ON Center console spot light. ON/OFF
      Light Control
      Display Default Content Setting
      Sensitivity NORMAL Function to adjust the ambient light sensitivity of the automatic light control system.*1 Light2/Light1/Normal/Dark1/Dark2
      Disp Ex ON Sen NORMAL Function to change the level of ambient light at which the system dims lights such as the combination meter indicator light, the A/C indicator light and the clock light.*2 LIGHT2/LIGHT1/NORMAL/DARK1/DARK2
      Disp Ex OFF Sen NORMAL Function to change the level of ambient light at which the system cancels the dimming of lights such as the combination meter indicator light, the A/C indicator light and the clock light.*3 LIGHT2/LIGHT1/NORMAL/DARK1/DARK2
      Automatic High Beam ON Automatic high beam system ON/OFF
      Lane CHG Flash CNT 3 times Lane change flasher system OFF/3 times/5 times/7 times/9 times/11 times

      Tech Tips

      The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle of the customer.

      *1
      System Setting A01ENCV
      Setting Dark2 Dark1 Normal Light1 Light2

      Tech Tips

      When the setting is closer to the "Light" side, the system turns the lights on even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before turning on the lights.

      *2
      System Setting A01ENCV
      Setting Dark2 Dark1 Normal Light1 Light2

      Tech Tips

      When the setting is closer to the "Light" side, the system dims the indicator lights even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before dimming the indicator lights.

      *3
      System Setting A01ENCV
      Setting Dark2 Dark1 Normal Light1 Light2

      Tech Tips

      When the setting is closer to the "Dark" side, the system cancels the dimming of the indicator lights even when the surrounding area is relatively dark. When the setting is closer to the "Light" side, the system waits until the surrounding area is brighter before canceling the dimming of the indicator lights.

  2. Door linked map light and personal light illumination control

    Mode 1: When door is opened, map light of opened door illuminates, or personal light illuminates

    Mode 2: When door is opened, all map lights and personal lights illuminate

    Mode 3: Map lights and personal lights are not linked to doors


    1. To change modes, press the map light assembly DOOR and on switch simultaneously, and then turn the engine switch from off to on (IG). Each engine switch off to on (IG) operation will change the mode (Mode 1 → Mode 2 → Mode 3 → Mode 1).

      Tech Tips

      After changing modes, the map light responds by blinking as follows: Mode 1: once; Mode 2: twice; Mode 3: three times.

  3. CUSTOMIZING FUNCTION WITH MULTI-DISPLAY

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Turn the engine switch to on (IG).

    2. Enter the following menus: Setup / Vehicle / Vehicle Settings / Vehicle Customization / Light Settings.

    3. Select the setting by referring to the table below.

      Display Default Contents Setting
      Light Sensor Sensitivity

      0

      (middle bar)

      		 Adjusts the ambient light sensitivity of the automatic light control system.* -2, -1, 0, +1 or +2
      Interior Lights Off Time 15 s This function controls the interior lights. OFF, 7.5 s, 15 s or 30 s
      Exterior Lights Off Time 15 s This function controls the exterior lights. OFF, 7.5 s, 15 s or 30 s
      Select Turn Flash Counts 3 times Lane change flasher system OFF/3 times/5 times/7 times/9 times/11 times

      Tech Tips

      The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle.

      *
      System Setting A01ENCV
      Setting -2 -1 0 +1 +2

      Tech Tips

      When the setting is closer to the "Light" side, the system turns the lights on even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before turning on the lights.