WASHER NOZZLE (for Front Side) INSTALLATION

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE WASHER NOZZLE SUB-ASSEMBLY (w/ PTC Heater)


    1. Connect the hose.

    2. A01EOK8

      Attach the 4 claws to install the washer nozzle.

    3. A01EN3T

      Connect the connector and attach the connector clamp.

  2. INSTALL WASHER NOZZLE SUB-ASSEMBLY (w/o PTC Heater)

    Tech Tips

    Use the same procedure to install the other washer nozzle


    1. A01ENZ0

      Attach the 3 clamps to install the washer nozzle.

    2. Connect the hose.

  3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A01EOFEE01

      Push in the ventilator louver to attach the 17 claws and install the ventilator louver.

    2. Install the 2 clips.

    3. A01EQS4

      Connect the washer hose.

  4. INSTALL HOOD TO COWL TOP SEAL


    1. A01EO3N

      Attach the 12 clips and 4 clamps to install the hood to cowl top seal.

  5. INSTALL FRONT FENDER MAIN SEAL LH


    1. A01ERY2

      Attach the 3 clips to install the fender main seal.

  6. INSTALL FRONT FENDER MAIN SEAL RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL UPPER RADIATOR SUPPORT SEAL


    1. Install the upper radiator support seal with the 3 clips.

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  9. INSTALL ENGINE ROOM SIDE COVER LH


    1. Install the engine room side cover LH with the 7 clips.

  10. INSTALL ENGINE ROOM SIDE COVER RH


    1. Install the engine room side cover RH with the 7 clips.

  11. INSTALL FRONT WIPER ARM LH


    1. A01ENQ2E01

      Stop the wiper motor at the automatic stop position.

    2. Clean the wiper pivot serrations with a wire brush.

    3. A01ESC2E01

      Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade come to the position shown in the illustration.

      Standard
      Position Specified Condition
      A 16.8 to 36.8 mm (0.661 to 1.45 in.)
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Tech Tips

      Hold down the wiper arm hinge with your hand while tightening the nut.

  12. INSTALL FRONT WIPER ARM RH


    1. A01ENQ2E01

      Stop the wiper motor at the automatic stop position.

    2. Clean the wiper pivot serrations with a wire brush.

    3. A01ES7AE01

      Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade come to the position shown in the illustration.

      Standard
      Position Specified Condition
      B 20.0 to 40.0 mm (0.787 to 1.57 in.)
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Tech Tips

      Hold down the wiper arm hinge with your hand while tightening the nut.

    4. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.