POWER MIRROR CONTROL SYSTEM Driver Side Power Mirror cannot be Adjusted with Power Mirror Switch

SYSTEM DESCRIPTION

This circuit detects the conditions of the outer mirror switch.

The outer mirror switch sends information about the operating condition of the mirror switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU. Mirror adjustment is controlled by the outer mirror control ECU.

WIRING DIAGRAM

A01EPSKE42
A01EPSKE45

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC


    1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. READ VALUE USING INTELLIGENT TESTER (OUTER MIRROR SWITCH)


    1. Check the Data List for proper functioning of the mirror master switch and mirror control switch Click here.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Mirror Selection SW (L) Mirror master switch signal for LH mirror / ON or OFF

      ON: Switch in L position

      OFF: Switch off or in R position

      		 -
      Mirror Selection SW (R) Mirror master switch signal for RH mirror / ON or OFF

      ON: Switch in R position

      OFF: Switch off or in L position

      		 -
      Mirror Position SW (R) Mirror control switch signal (right) / ON or OFF

      ON: Right switch on

      OFF: Any switch except right on or all switches off

      		 -
      Mirror Position SW (L) Mirror control switch signal (left) / ON or OFF

      ON: Left switch on

      OFF: Any switch except left on or all switches off

      		 -
      Mirror Position SW (Up) Mirror control switch signal (up) / ON or OFF

      ON: Up switch on

      OFF: Any switch except up on or all switches off

      		 -
      Mirror Position SW (Dwn) Mirror control switch signal (down) / ON or OFF

      ON: Down switch on

      OFF: Any switch except down on or all switches off

      		 -
      OK
      On tester screen, each item changes between ON and OFF according to above chart.

    NG

    INSPECT OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER MIRROR CONTROL FUNCTION)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check the power mirror control function Click here.

      Mirror
      Tester Display Test Part Control Range Diagnostic Note
      LH Mirror Up/Down Mirror vertical operation Up / OFF / Down -
      LH Mirror Right/Left Mirror horizontal operation Right / OFF / Left -
      RH Mirror Up/Down Mirror vertical operation Up / OFF / Down -
      RH Mirror Right/Left Mirror horizontal operation Right / OFF / Left -
      Result
      Result Proceed to
      Outer rear view mirror (for Driver Side) does not operate normally A
      Outer rear view mirror (for Driver Side) operates normally B

    B

    REPLACE OUTER MIRROR CONTROL ECU Click here

    A

  4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Driver Side)


    1. A01ERAVE01

      for LHD:


      1. Remove the mirror LH Click here.

      2. Apply battery voltage and check the operation of the power mirror.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 7 (MV)

        Battery negative (-) → Terminal 8 (M+)

        		 Turns upward (A)

        Battery negative (-) → Terminal 7 (MV)

        Battery positive (+) → Terminal 8 (M+)

        		 Turns downward (B)

        Battery positive (+) → Terminal 9 (MH)

        Battery negative (-) → Terminal 8 (M+)

        		 Turns left (C)

        Battery negative (-) → Terminal 9 (MH)

        Battery positive (+) → Terminal 8 (M+)

        		 Turns right (D)
    2. A01ENTZE01

      for RHD:


      1. Remove the mirror RH Click here.

      2. Apply battery voltage and check the operation of the power mirror.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 7 (MV)

        Battery negative (-) → Terminal 8 (M+)

        		 Turns upward (A)

        Battery negative (-) → Terminal 7 (MV)

        Battery positive (+) → Terminal 8 (M+)

        		 Turns downward (B)

        Battery positive (+) → Terminal 9 (MH)

        Battery negative (-) → Terminal 8 (M+)

        		 Turns left (C)

        Battery negative (-) → Terminal 9 (MH)

        Battery positive (+) → Terminal 8 (M+)

        		 Turns right (D)

    NG

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (for Driver Side) Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU - OUTER REAR VIEW MIRROR ASSEMBLY)


    1. A01EQ3YE21

      for LHD:


      1. Disconnect the I18 ECU connector.

      2. Disconnect the I36 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-18 (M+L) - I36-8 (M+) Always Below 1 Ω
        I18-19 (MHL) - I36-9 (MH)
        I18-20 (MVL) - I36-7 (MV)
        I36-8 (M+) - Body ground Always 10 kΩ or higher
        I36-9 (MH) - Body ground
        I36-7 (MV) - Body ground
    2. A01EQ3YE22

      for RHD:


      1. Disconnect the I32 ECU connector.

      2. Disconnect the I33 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I32-38 (M+R) - I33-8 (M+) Always Below 1 Ω
        I32-39 (MHR) - I33-9 (MH)
        I32-40 (MVR) - I33-7 (MV)
        I33-8 (M+) - Body ground Always 10 kΩ or higher
        I33-9 (MH) - Body ground
        I33-7 (MV) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER MIRROR CONTROL ECU Click here

  6. INSPECT OUTER MIRROR SWITCH ASSEMBLY


    1. A01EPAIE04

      Remove the outer mirror switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      8 (M+) - 6 (E) Up switch pushed 90 to 110 Ω
      Down switch pushed 437 to 502 Ω
      Left switch pushed 744 to 856 Ω
      Right switch pushed 207 to 253 Ω
      No switches pushed 10 kΩ or higher
      3 (MSW) - 6 (E) Mirror master switch L 90 to 110 Ω
      Mirror master switch R Below 1 Ω
      Mirror master switch off 10 kΩ or higher

    NG

    REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)


    1. A01EQWQE01

      Disconnect the E1 ECU connector.

    2. Disconnect the E94 switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E1-2 (MIRE) - E94-6 (E) Always Below 1 Ω
      E1-11 (MIRB) - E94-8 (M+) Always Below 1 Ω
      E1-12 (MIRS) - E94-3 (MSW) Always Below 1 Ω
      E94-8 (M+) - Body ground Always 10 kΩ or higher
      E94-6 (E) - Body ground Always 10 kΩ or higher
      E94-3 (MSW) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)