OUTER REAR VIEW MIRROR REASSEMBLY

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. INSTALL SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)


    1. Install the side television camera with the 3 screws.

    2. Install the body.


      1. Attach the 2 guides and body.

        Note

        Be careful not to break the guide.

    3. Install the body cover.


      1. Install the body with the 5 screws.

    4. A01EP8E

      Connect the connector.

    5. Attach the connector to the wire clip.

    6. Install the base.


      1. Attach the guide.

      2. Using "TORX" socket wrench T25, install the base with 3 new screws.

        Note

        When installing the base, check that the wire harness is not caught between the base and housing. Failure to do so may cause a short circuit.

    7. Install the lower mirror cover.


      1. Attach the 4 claws and install the new lower mirror cover.

    8. Install the gasket.


      1. Attach the 9 guides and install the gasket.

      2. A01EPV5E02
        Text in Illustration
        *1 New Vinyl Tape
        *a Marking

        Align the marking on the wire harness with the marking on the end of the wire harness insertion hole of the gasket as shown in the illustration, and wrap them with new vinyl tape starting from the gasket marking.

        Standard
        Area Specified Condition
        a 50.0 mm (1.97 in.)

        Note

        If the vinyl tape is wrinkled, water may run down the wire harness and enter the vehicle. Make sure to wind the vinyl tape properly.

      3. A01ES2HE01
        Text in Illustration
        *1 New Vinyl Tape

        Wrap new vinyl tape as shown in the illustration.

        Standard
        Area Specified Condition
        a 30.0 mm (1.18 in.)
        b 50.0 mm (1.97 in.)

  2. INSTALL SIDE TURN SIGNAL LIGHT ASSEMBLY LH


    1. Install the side turn signal light assembly LH.


      1. Connect the connector.

      2. Install the side turn signal light assembly LH with the 3 screws.

    2. Install the outer mirror cover.


      1. A01ERI5E01
        Text in Illustration
        *1 Rib

        Insert the rib on the outer edge of the cover into the groove of the mirror body.

        Note

        Do not scratch the turn light.

      2. A01ENUME01
        Text in Illustration
        *1 Rib

        Confirm that the cover and mirror body are aligned properly, and then push the outer end of the cover to attach the outer claws.

        Note


        • Make sure that the upper ribs of the cover shown in part A of the illustration are properly attached to the mirror body.

        • Make sure that the ribs of the mirror body shown in part B of the illustration are not protruding from the cover.

      3. A01EQXX

        While making sure that the rib of the cover fits properly into the groove of the mirror body, squeeze the inner end of the cover and the mirror body together to attach the inner claws.

    3. A01ERXL

      Push on the cover at the locations of the 8 claws to confirm that the claws are attached properly.

    4. Check that there is no gap between the cover and mirror body.

      Tech Tips

      If there is a gap between the cover and body, noise will occur during driving.

  3. INSTALL OUTER MIRROR LIGHT ASSEMBLY BULB


    1. A01ENGQ

      Turn the bulb in the direction indicated by the arrow and install it to the outer mirror.

  4. INSTALL OUTER REAR VIEW MIRROR GLASS

    A01EP9R

    1. Connect the 3 connectors.

    2. A01EOAB

      Attach the 4 claws to install the mirror glass.

  5. ADJUST SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)

    Click here