POWER MIRROR CONTROL SYSTEM Reverse Shift-linked Function of Power Mirrors does not Operate

SYSTEM DESCRIPTION

When the reverse signal is sent from the ECM through the CAN communication line to the outer mirror control ECU, the outer mirror control ECU activates the outer rear view mirror LH and RH reverse shift-linked function.

Tech Tips

The reverse shift-linked function will not occur when the mirror master switch is in the neutral position (off).

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC


    1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. CHECK OPERATION OF SHIFT INDICATOR


    1. Check that the shift indicator of the combination meter operates normally.

      OK
      Shift indicator of combination meter operates normally.

    NG

    GO TO METER / GAUGE SYSTEM Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)


    1. Check the Data List for proper functioning of the mirror position sensor Click here.

      Mirror
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      RH Mir Position Sensor V RH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
      LH Mir Position Sensor V LH side mirror vertical sensor voltage / MIN: 0 V, MAX: 5 V Within range from 0 to 5 V -
      OK
      When mirror control switch is operated to turn mirror upward or downward, voltage changes within range shown in above chart.
      Result
      Result Proceed to
      LH side mirror does not operate normally A
      RH side mirror does not operate normally B
      Mirror operates normally C

    B

    CHECK OUTER MIRROR CONTROL ECU (POWER SOURCE FOR MIRROR POSITION SENSOR) Click here

    C

    REPLACE OUTER MIRROR CONTROL ECU Click here

    A

  4. CHECK OUTER MIRROR CONTROL ECU (POWER SOURCE FOR MIRROR POSITION SENSOR)

    A01ENO3E08

    1. for LHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I18-2 (LVC) - I18-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-3 (LE1) - Body ground Always Below 1 Ω

    2. for RHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I32-2 (LVC) - I32-3 (LE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I32-3 (LE1) - Body ground Always Below 1 Ω

    NG

    REPLACE OUTER MIRROR CONTROL ECU Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU)


    1. A01EOURE10

      for LHD:


      1. Disconnect the I18 ECU connector.

      2. Disconnect the I36 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-2 (LVC) - I36-10 (VC) Always Below 1 Ω
        I18-3 (LE1) - I36-21 (E1)
        I18-4 (VSR) - I36-22 (VSRL)
        I36-10 (VC) - Body ground Always 10 kΩ or higher
        I36-21 (E1) - Body ground
        I36-22 (VSRL) - Body ground

    2. for RHD:


      1. Disconnect the I32 ECU connector.

      2. Disconnect the I35 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I32-2 (LVC) - I35-10 (VC) Always Below 1 Ω
        I32-3 (LE1) - I35-21 (E1)
        I32-4 (VSR) - I35-22 (VSRL)
        I35-10 (VC) - Body ground Always 10 kΩ or higher
        I35-21 (E1) - Body ground
        I35-22 (VSRL) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH Click here

  6. CHECK OUTER MIRROR CONTROL ECU (POWER SOURCE FOR MIRROR POSITION SENSOR)

    A01ENO3E09

    1. for LHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I18-22 (RVC) - I18-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-23 (RE1) - Body ground Always Below 1 Ω

    2. for RHD:


      1. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Switch Condition Specified Condition
        I32-22 (RVC) - I32-23 (RE1) Engine switch on (IG) 4.7 to 5.5 V

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I32-23 (RE1) - Body ground Always Below 1 Ω

    NG

    REPLACE OUTER MIRROR CONTROL ECU Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU)


    1. A01EOURE11

      for LHD:


      1. Disconnect the I18 ECU connector.

      2. Disconnect the I34 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I18-22 (RVC) - I34-10 (VC) Always Below 1 Ω
        I18-23 (RE1) - I34-21 (E1)
        I18-24 (VSRR) - I34-22 (VSSR)
        I34-10 (VC) - Body ground Always 10 kΩ or higher
        I34-21 (E1) - Body ground
        I34-22 (VSSR) - Body ground

    2. for RHD:


      1. Disconnect the I32 ECU connector.

      2. Disconnect the I33 mirror connector.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        I32-22 (RVC) - I33-10 (VC) Always Below 1 Ω
        I32-23 (RE1) - I33-21 (E1)
        I32-24 (VSRR) - I33-22 (VSSR)
        I33-10 (VC) - Body ground Always 10 kΩ or higher
        I33-21 (E1) - Body ground
        I33-22 (VSSR) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH Click here