WINDSHIELD GLASS REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE ENGINE ROOM SIDE COVER LH


    1. Remove the 7 clips and engine room side cover LH.

      A01EN5SE01

  3. REMOVE ENGINE ROOM SIDE COVER RH


    1. Remove the 7 clips and engine room side cover RH.

      A01EPFTE01

  4. REMOVE UPPER RADIATOR SUPPORT SEAL


    1. A01ENLH

      Remove the 3 clips and upper radiator support seal.

  5. REMOVE FRONT FENDER MAIN SEAL LH


    1. A01ERY2

      Using a clip remover, detach the 3 clips and remove the fender main seal.

  6. REMOVE FRONT FENDER MAIN SEAL RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. REMOVE FRONT WIPER ARM LH


    1. Remove the nut, wiper arm and blade.

  8. REMOVE FRONT WIPER ARM RH


    1. Remove the nut, wiper arm and blade.

  9. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A01EQS4

      Disconnect the washer hose.

    2. A01EOFE

      Remove the 2 clips.

    3. Detach the 17 claws and remove the cowl top ventilator louver sub-assembly.

  10. REMOVE WINDSHIELD OUTSIDE MOULDING LH


    1. A01ENLCE01

      Remove the windshield outside moulding.


      1. Put protective tape around the moulding.

      2. Using a moulding remover, detach the 6 clips and remove the moulding.

        Note


        • When removing the windshield outside moulding, be careful not to damage the roof drip side finish moulding clip labeled A in the illustration.

        • If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.

  11. REMOVE WINDSHIELD OUTSIDE MOULDING RH

    Tech Tips

    Use the same procedures described for the LH side.

  12. REMOVE NO. 4 WINDSHIELD MOULDING PAD

    A01EMW1

    1. Remove the 4 No. 4 windshield moulding pads.

      Tech Tips

      Use the same procedure to remove the 4 pads on the other side.

  13. REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

    Tech Tips

    Perform the following procedures if replacing any No. 3 windshield outside moulding clip(s).


    1. Put a 4 mm (0.157 in.) drill bit into a drill.

    2. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill.

      Tech Tips

      Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. A01ERFAE01

      Lightly press the drill against the No. 3 windshield outside moulding clip(s), drill off the flanges of the No. 3 windshield outside moulding clip(s), and remove the No. 3 windshield outside moulding clip(s).

      CAUTION:

      Be careful of the drilled No. 3 windshield outside moulding clips as they may become hot.

      Note


      • Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

      • Do not pry the No. 3 windshield outside moulding clips with the drill, because this may cause damage to the installation holes of the No. 3 windshield outside moulding clips or the drill bit.

    4. Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.

      Tech Tips

      Use the same procedure to remove the clip(s) on the other side.

  14. REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP

    A01ERWF

    Tech Tips

    Perform the following procedures if replacing any roof drip side finish moulding clips.


    1. Remove the roof drip side finish moulding clips.

      Tech Tips

      Use the same procedure to remove the clip on the other side.

  15. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

    A01EPTJ

    Tech Tips

    Use the same procedure to remove the front assist grip on the other side.


    1. Detach the 4 claws and remove the 2 assist grip plugs.

    2. A01EQ8Y

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the front assist grip.

  16. REMOVE FRONT PILLAR GARNISH LH

    A01ENLZ

    1. Detach the clip and 3 guides.

    2. Disconnect the speaker connector and then remove the front pillar garnish.

    3. A01EO6AE01

      Protect the curtain shield airbag.


      1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  17. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedures described for the LH side.

  18. REMOVE MAP LIGHT ASSEMBLY


    1. Using a screwdriver, detach the 2 claws and open the 2 covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. Detach the 2 clips and 2 guides.

    4. Disconnect the 2 connectors and then remove the map light.

      A01EPYHE01

  19. REMOVE VISOR BRACKET COVER

    A01EPY8

    Tech Tips

    Use the same procedure to remove the visor bracket cover on the other side.


    1. Detach the 4 claws and remove the visor bracket cover.

  20. REMOVE VISOR ASSEMBLY LH

    A01EQA3

    1. Remove the 2 screws and visor.

  21. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  22. REMOVE VISOR HOLDER

    A01EORQE02

    Tech Tips

    Use the same procedure to remove the visor holder on the other side.


    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  23. REMOVE CENTER VISOR ASSEMBLY LH

    A01EOTVE01

    1. Using a screwdriver, pry off the cover to detach the 2 clips and remove the center visor.

      Tech Tips

      Tape the screwdriver tip before use.

  24. REMOVE CENTER VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  25. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER


    1. A01EQMJ

      Detach the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow shown in the illustration..

    2. A01EQY5

      Detach the 2 claws and remove the inner rear view mirror stay holder cover.

  26. REMOVE INNER REAR VIEW MIRROR ASSEMBLY


    1. A01EPKI

      Disconnect the connector.

    2. Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror assembly.

  27. REMOVE RAIN SENSOR COVER


    1. Slide the No. 2 cover in the direction of the arrow labeled (1).

      A01ES6ME01

    2. Pull the stopper in the direction of the arrow labeled (2) to remove the rain sensor cover.

  28. REMOVE RAIN SENSOR


    1. A01ESMAE01

      Release the stopper by pulling it in the direction of the arrow, and separate the rain sensor.

    2. Disconnect the connector and remove the rain sensor.

    3. When replacing the rain sensor tape:


      1. Remove the rain sensor tape.

  29. REMOVE ROOF HEADLINING


    1. Partially remove the roof headlining.

      Tech Tips

      It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

      Refer to the following procedures Click here.

  30. REMOVE WINDSHIELD OUTSIDE MOULDING

    A01EQ4ZE01

    1. Using a knife, cut off the moulding as shown in the illustration.

      Note

      Be careful not to damage the vehicle body.

    2. Pull the shaded area shown in the illustration by hand to remove the windshield outside moulding.

      Tech Tips

      Make a partial cut in the moulding. Then pull and remove it by hand.

  31. REMOVE WINDSHIELD GLASS

    A01ERKLE01

    1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.

    2. From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

    3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

      Note


      • When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

      • To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.

    4. A01EMZ6E01

      Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

      Note

      Matchmarks do not need to be placed if not reusing the glass.

    5. A01ES3ME01

      w/o Heated Windshield Defroster:


      1. Disconnect the connector A.

        Tech Tips

        w/o Heated Windshield Defroster: The vehicle only has connector A.

    6. w/ Heated Windshield Defroster:

      Disconnect the 3 connectors.

    7. Cut through the adhesive by pulling the piano wire around the glass.

      Note

      Leave as much adhesive on the vehicle body as possible when removing the glass.

    8. Disconnect the stoppers.

    9. Using suction cups, remove the glass.

  32. REMOVE NO. 2 WINDSHIELD GLASS STOPPER


    1. Using a scraper, remove the 2 stoppers.

  33. REMOVE WINDSHIELD GLASS ADHESIVE DAM


    1. Using a scraper, remove the dam.

  34. REMOVE FRONT INNER WINDOW MOULDING COVER LH


    1. Using a scraper, remove the cover.

  35. CLEAN WINDSHIELD GLASS

    A01EQB8

    1. Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.

    2. Clean the outer circumference of the glass with non-residue solvent.

      Note


      • Do not touch the glass surface after cleaning it.

      • Be careful not to damage the glass.

      • Even if using new glass, clean the glass with non-residue solvent.

  36. REMOVE WINDSHIELD GLASS STOPPER


    1. Remove the 2 windshield glass stoppers.

  37. CLEAN VEHICLE BODY

    A01EOBUE11

    1. Clean and shape the contact surface of the vehicle body.


      1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surface of the vehicle body with cleaner.

      Tech Tips

      Even if all the adhesive has been removed, clean the vehicle body.