POWER WINDOW REGULATOR MOTOR (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01ENEKE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the rear door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE REAR UPPER DOOR ARMREST BASE PANEL


    1. A01EO3E

      Using a moulding remover, detach the 6 claws.

    2. Disconnect the connector and remove the rear upper door armrest base panel LH and rear power window regulator switch assembly.

  4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01ERTKE01

      Remove the 2 screws.

    2. Detach the 11 clips.

    3. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

      Tech Tips

      Make sure that the pin labeled A in the illustration is detached from the door panel.

    4. Disconnect the connector.

    5. A01EPPA

      Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

  5. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP


    1. A01ENT3

      Detach the 4 clips and remove the front inner door glass weatherstrip LH from the front door trim board sub-assembly LH.

      Note


      • Squeeze the metal clip to remove it.

      • The metal clip may be deformed if it is forcibly pulled.

  6. REMOVE REAR SPEAKER SET


    1. Disconnect the speaker connector.

    2. Remove the 3 screws.

    3. Detach the claw and remove the speaker.

      Note

      Do not touch the cone part of the speaker.

      A01EPDOE01

  7. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01ERCQ

      Using a clip remover, detach the 6 clamps.

    2. Remove the bolt and disconnect the 2 connectors.

    3. Remove the rear door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  8. REMOVE REAR DOOR GLASS RUN


    1. A01ES1E

      Remove the rear door glass run LH from the window frame.

  9. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01EOAU

      Remove the 2 bolts.

    2. Remove the screw and rear door rear lower window frame sub-assembly LH.

  10. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A01EP1N

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01ENIQ

      Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. A01EON1E05
      Text in Illustration
      *1 Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and become damaged.

    2. Remove the 3 bolts and rear door window regulator sub-assembly LH.

      Note

      Be careful when removing the bolts as the rear door window regulator sub-assembly LH may fall and become damaged.

    3. Remove the temporary bolt from the rear door window regulator sub-assembly LH.

  13. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01EQYO

      Using a T25 "TORX" driver, remove the 3 screws and motor.

      Note

      Be careful when removing the screws as the motor may fall and become damaged.