POWER WINDOW CONTROL SYSTEM Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION


WIRING DIAGRAM

A01EPBRE12

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK LIN COMMUNICATION SYSTEM


    1. Check for LIN communication system DTCs related to the power window control system Click here.

      OK
      LIN communication system DTCs are not output.

    NG

    GO TO LIN COMMUNICATION SYSTEM Click here

    OK

  2. CHECK FOR DTC (B2312)


    1. Check if DTC B2312 is output Click here.

      OK
      DTC B2312 is not output.

    NG

    GO TO DTC B2312 Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR MOTOR RH)


    1. Use the Data List to check if the power window regulator motor is functioning properly Click here.

      RR-Door Motor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door P/W Up SW Rear power window RH manual up signal / ON or OFF

      ON: Rear power window RH manual up switch operated

      OFF: Rear power window RH switch not operated

      		 -
      RR Door P/W Down SW Rear power window RH manual down signal / ON or OFF

      ON: Rear power window RH manual down switch operated

      OFF: Rear power window RH switch not operated

      		 -
      OK
      Display changes according to operation of rear power window switch RH.

    NG

    CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH RH - BODY GROUND) Click here

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

  4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH RH - BODY GROUND)


    1. A01EPWZE06

      Disconnect the J3 switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J3-5 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR RH - BATTERY AND BODY GROUND)


    1. A01ENOPE12

      Disconnect the J4 motor connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J4-2 (B) - Body ground Always 11 to 14 V
      Standard Resistance
      Tester Connection Condition Specified Condition
      J4-1 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH RH - REAR POWER WINDOW REGULATOR MOTOR RH)


    1. A01ERZLE12

      Disconnect the J3 switch connector.

    2. Disconnect the J4 motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J3-2 (UP) - J4-10 (UP) Always Below 1 Ω
      J3-10 (DOWN) - J4-7 (DOWN) Always Below 1 Ω
      J3-4 (AUTO) - J4-4 (AUTO) Always Below 1 Ω
      J3-2 (UP) or J4-10 (UP) - Body ground Always 10 kΩ or higher
      J3-10 (DOWN) or J4-7 (DOWN) - Body ground Always 10 kΩ or higher
      J3-4 (AUTO) or J4-4 (AUTO) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

    A01EQ4OE03

    1. Remove the rear power window regulator switch RH Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      2 (UP) - 5 (GND) Manual up operation Below 1 Ω
      10 (DOWN) - 5 (GND) Manual down operation Below 1 Ω

    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH Click here

    OK

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here