RADIATOR REMOVAL


  1. REMOVE V-BANK COVER SUB-ASSEMBLY


    1. A01EN38E01

      Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.

  2. REMOVE ENGINE ROOM SIDE COVER LH


    1. Remove the 7 clips and engine room side cover LH.

      A01EN5SE01

  3. REMOVE ENGINE ROOM SIDE COVER RH


    1. Remove the 7 clips and engine room side cover RH.

      A01EPFTE01

  4. REMOVE UPPER RADIATOR SUPPORT SEAL


    1. A01ENLH

      Remove the 3 clips and upper radiator support seal.

  5. REMOVE RADIATOR GRILLE


    1. A01EQD7E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the radiator grille assembly.

    2. Remove the screw and 2 clips.

    3. Detach the 4 clips and partially remove the upper radiator seal.

    4. Detach the 14 claws and remove the radiator grille assembly.

    5. w/ Wide View Front Monitor System:

      Disconnect the connector.

  6. REMOVE RADIATOR SIDE DEFLECTOR RH (w/o Air Cooled Transmission Oil Cooler)


    1. A01EQ8A

      Using a clip remover, remove the 5 clips and side deflector.

  7. REMOVE RADIATOR SIDE DEFLECTOR LH


    1. A01EPV6

      Using a clip remover, remove the 5 clips and side deflector.

  8. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. A01EQP2

      Remove the 3 bolts and 2 screws.

    2. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.

  9. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. A01EN7K

      Remove the 10 bolts and No. 1 engine under cover.

  11. DRAIN ENGINE COOLANT

    CAUTION:

    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    A01EN5HE01

    1. Loosen the radiator drain cock plug.

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

    2. Remove the radiator cap. Then drain the coolant from the radiator.

    3. Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.

    4. Tighten the 2 cylinder block drain cock plugs.

      Torque:
      13 N*m  { 130 kgf*cm, 10 ft.*lbf }

    5. Tighten the radiator drain cock plug by hand.

  12. REMOVE AIR CLEANER HOSE ASSEMBLY


    1. A01EPIO

      Disconnect the vacuum hose and No. 2 ventilation hose.

    2. Loosen the 2 hose clamps.

    3. Remove the air cleaner hose.

  13. REMOVE NO. 1 RADIATOR HOSE

  14. REMOVE NO. 2 RADIATOR HOSE

  15. REMOVE FAN SHROUD


    1. A01ESC5

      Loosen the 4 nuts holding the fluid coupling fan.

    2. Remove the fan and generator V belt Click here.

    3. A01EOA5E01

      Disconnect the reservoir hose from the upper radiator tank.

    4. w/ Air Cooled Transmission Oil Cooler:

      Detach the claw to open the flexible hose clamp.

    5. Remove the 2 bolts and disconnect the oil cooler tube from the fan shroud.

    6. Remove the 2 bolts holding the fan shroud.

    7. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the coupling fan.

      Note

      Be careful not to damage the radiator core.

    8. Remove the fan pulley.

  16. REMOVE RADIATOR ASSEMBLY


    1. A01EO0L

      Disconnect the 2 oil cooler hoses.

    2. A01ES7X

      Remove the 4 bolts and radiator.