FUEL INJECTOR INSTALLATION

INSTALL FUEL INJECTOR ASSEMBLY
1. Attach the 3 clamps to install the No. 6 wire harness to the delivery pipe RH.
2. Attach the 3 clamps to install the No. 7 wire harness to the delivery pipe LH.
3. Apply gasoline or spindle oil to a new O-ring and install it to the injector.
  
  Note
  
  Make sure that there is no damage or foreign material in the groove of the injector when installing the O-ring.
4. Connect the injector connector.
5. Install the injector to the delivery pipe as shown in the illustration.
  Note
  
  Make sure that there are no scratches or foreign matter in or around the insertion hole of the delivery pipe.
  
  When inserting the injector, be careful not to damage the O-ring.
  
  Attach the part of the injector labeled B between the parts of the delivery pipe labeled A.
6. Check that each injector is installed to the delivery pipe facing the direction shown in the illustration.
INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH
1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head LH.
2. Install the delivery pipe (with injectors) to the cylinder head LH.
3. Install the 2 bolts.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
  
  Note
  
  Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.
4. Connect the No. 7 wire harness connector.
INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH
1. Install the 2 delivery pipe spacers and 4 insulators to the cylinder head RH.
2. Install the delivery pipe (with injectors) to the cylinder head RH.
3. Install the 2 bolts.
  
  Torque:
  
  21 N*m { 214 kgf*cm, 15 ft.*lbf }
  
  Note
  
  Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.
4. Connect the No. 6 wire harness connector.
5. Connect the ventilation hose.
CONNECT NO. 1 FUEL HOSE
1. Connect the No. 1 fuel hose to the fuel delivery pipe LH Click here.
CONNECT NO. 1 FUEL TUBE
1. LH Side:
  
  Connect the No. 1 fuel tube to the delivery pipe LH Click here.
2. RH Side:
  
  Connect the No. 1 fuel tube to the delivery pipe RH (for metallic type) Click here.
CONNECT NO. 2 FUEL TUBE
1. Connect the No. 2 fuel tube to the fuel pressure regulator Click here.
INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
1. Install the No. 1 engine cover sub-assembly.
INSTALL NO. 3 ENGINE COVER
1. Install the No. 3 engine cover.
INSTALL AIR CLEANER HOSE ASSEMBLY
1. Install the air cleaner hose so that the protrusion of the air cleaner cap aligns with the groove of the hose as shown in the illustration.
2. Tighten the 2 clamps.
  
  Torque:
  
  2.5 N*m { 25 kgf*cm, 22 in.*lbf }
3. Connect the vacuum hose.
4. Connect the No. 2 ventilation hose.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSPECT FOR FUEL LEAK
1. Connect the intelligent tester to the DLC3.
2. Turn the engine switch on (IG) and intelligent tester on.
  
  Note
  
  Do not start the engine.
3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump Speed Control.
4. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
INSTALL V-BANK COVER SUB-ASSEMBLY
1. Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.
INSTALL UPPER RADIATOR SUPPORT SEAL
1. Install the upper radiator support seal with the 3 clips.
INSTALL ENGINE ROOM SIDE COVER LH
1. Install the engine room side cover LH with the 7 clips.
INSTALL ENGINE ROOM SIDE COVER RH
1. Install the engine room side cover RH with the 7 clips.