SUSPENSION CONTROL CYLINDER REMOVAL


  1. REMOVE TAILPIPE ASSEMBLY


    1. Remove the bolt, clamp and gasket.

    2. Remove the tailpipe from the 2 exhaust pipe supports.

    3. Remove the bolt and clamp, and then disconnect the tailpipe from the center exhaust pipe.

  2. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    1. Remove the 4 bolts.

    2. Remove the center exhaust pipe from the 3 exhaust pipe supports.

    3. Remove the 2 gaskets from the front exhaust pipe and front No. 2 exhaust pipe.

  3. REMOVE HEIGHT CONTROL UNIT INSULATOR

    A01EO08

    1. Remove the 3 bolts and insulator from the control unit.

  4. DISCHARGE SUSPENSION FLUID PRESSURE


    1. A01ERV4

      Connect a hose to the bleeder plug for the height control accumulator and loosen the bleeder plug.

    2. Discharge the suspension fluid pressure.

    3. After the fluid pressure has dropped and oil has drained out, tighten the bleeder plug and remove the hose.

      Torque:
      6.9 N*m  { 70 kgf*cm, 61 in.*lbf }

  5. REMOVE NO. 7 HEIGHT CONTROL TUBE

    A01ENL2

    1. Using a union nut wrench, remove the control tube from the control valve and pump accumulator.

  6. REMOVE SUSPENSION CONTROL PUMP ACCUMULATOR ASSEMBLY

    A01ER5G

    1. Remove the 3 nuts and pump accumulator.

  7. REMOVE CLAMP


    1. Remove the clamp from the 3 height control tubes.

  8. REMOVE NO. 6 HEIGHT CONTROL TUBE

    A01ER67E01

    1. Using a union nut wrench, remove the No. 6 height control tube from the control valve and center cylinder.

  9. REMOVE NO. 6 HEIGHT CONTROL TUBE LH


    1. Using a union nut wrench, remove the No. 6 height control tube LH from the control valve and center cylinder.

      A01EPNQE01

  10. REMOVE NO. 5 HEIGHT CONTROL TUBE LH

    A01EOP1E01

    1. Using a union nut wrench, remove the No. 5 height control tube LH from the control valve and center cylinder.

  11. REMOVE NO. 5 HEIGHT CONTROL TUBE


    1. Using a union nut wrench, remove the No. 5 height control tube from the control valve and center cylinder.

      A01ENVNE01

  12. DISCONNECT REAR NO. 4 HEIGHT CONTROL TUBE


    1. A01EN0FE01

      Disconnect the connector.

    2. Remove the union bolt and gasket, then disconnect the rear No. 4 height control tube from the control valve.

  13. REMOVE NO. 1 HEIGHT CONTROL VALVE ASSEMBLY

    A01EO7K

    1. Remove the 3 nuts and control valve.

    2. Remove the 3 bolt holders and 3 bolt cushions from the control valve.

  14. DISCONNECT NO. 3 HEIGHT CONTROL TUBE

    A01ERXO

    1. Remove the union bolt and gasket, then disconnect the No. 3 height control tube from the control cylinder.

  15. DISCONNECT NO. 4 HEIGHT CONTROL TUBE LH

    A01ESCH

    1. Remove the union bolt and gasket, then disconnect the No. 4 height control tube from the control cylinder.

  16. DISCONNECT NO. 4 HEIGHT CONTROL TUBE

    A01ERAO

    1. Remove the union bolt and gasket, then disconnect the No. 4 height control tube from the control cylinder.

  17. DISCONNECT NO. 3 HEIGHT CONTROL TUBE LH

    A01EMXU

    1. Remove the union bolt and gasket, then disconnect the No. 3 height control tube from the control cylinder.

  18. REMOVE HEIGHT CONTROL BRACKET WITH CYLINDER ASSEMBLY

    A01ES7M

    1. Remove the 2 bolts and bracket with cylinder.

  19. REMOVE CENTER SUSPENSION CONTROL CYLINDER SUB-ASSEMBLY

    A01ES47

    1. Remove the 2 nuts and cylinder from the bracket.