ACTIVE HEIGHT CONTROL PUMP AND MOTOR INSTALLATION


  1. INSTALL HEIGHT CONTROL PUMP AND MOTOR ASSEMBLY


    1. A01ENUI

      Install the pump and motor with the 3 bolts.

      Torque:
      31 N*m  { 316 kgf*cm, 23 ft.*lbf }
    2. A01ENS5

      Connect the 2 connectors and 3 clamps.

  2. INSTALL HEIGHT CONTROL TUBE CLAMP


    1. A01EPVEE01

      Install the tube clamp with the 2 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. Connect the reservoir hose to the tube clamp.

  3. CONNECT REAR NO. 6 HEIGHT CONTROL TUBE


    1. A01EOGYE01

      Using a union nut wrench, connect the control tube to the pump and motor.

      Torque:
      without union nut wrench
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }
      with union nut wrench
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

      • The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.

  4. BLEED AIR FROM SUSPENSION FLUID


    1. A01ESCZ

      With the engine stopped, fill the reservoir tank with fluid.

      Note

      When the engine starts, the pump operates and fluid is supplied to each cylinder from the reservoir tank. Therefore, add the necessary amount of fluid so that the reservoir tank does not become empty.

      Tech Tips

      At this point, the vehicle height is low because the pressure of the cylinders is low.

    2. With the vehicle on a level surface, start the engine and set the vehicle height to NORMAL with the suspension control switch.

    3. When the vehicle height becomes NORMAL and the pump stops, stop the engine.

    4. A01ES50

      Connect a hose to the bleeder plug of the front left side or right side control valve, then loosen the bleeder plug.

      CAUTION:

      Be careful when loosening the control valve bleeder plug because the front vehicle height drops rapidly.

    5. After the fluid containing air stops coming out, retighten the bleeder plug.

      Torque:
      8.3 N*m  { 85 kgf*cm, 73 in.*lbf }

      Tech Tips

      If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

    6. A01ENFN

      Connect a hose to the bleeder plug of the rear left side or right side control valve, then loosen the bleeder plug.

      CAUTION:

      Be careful when loosening the control valve bleeder plug because the rear vehicle height drops rapidly.

    7. After the fluid containing air stops coming out, retighten the bleeder plug.

      Torque:
      8.3 N*m  { 85 kgf*cm, 73 in.*lbf }

      Tech Tips

      If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

    8. Repeat the previous 4 procedures until the fluid containing air stops coming out.

  5. CHECK FLUID LEVEL IN RESERVOIR


    1. A01EQWG

      With the vehicle empty, after setting the vehicle height to NORMAL from LO, check the indicator to make sure the vehicle height is NORMAL and check that the fluid level in the reservoir tank is within the specified range (MAX, MIN).

      Tech Tips

      After changing the vehicle height from LO to NORMAL, do not stop the engine for 25 seconds because the pressure control for the main accumulator is operating. After that, check the fluid level.

  6. INSPECT FOR SUSPENSION FLUID LEAK


    1. Check the torque value of the rear No. 5 height control tube union nuts.

      Torque:
      without union nut wrench
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }
      with union nut wrench
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).

      • The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.

    2. Check for fluid leakage from the parts and connections.

      A01ER8EE01

      Tech Tips

      For union nuts and union bolts not shown in the illustration, refer to the installation procedures for each title.

  7. INSTALL FUEL TANK FILLER PIPE PROTECTOR


    1. A01EQ64

      Using a T30 "TORX" socket wrench, install the pipe protector with the 3 screws and 2 new grommets.

  8. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

    A01ES3R

    1. Install the protector with 2 new grommets.

    2. Install the 2 screws.

  9. INSTALL REAR BUMPER COVER


    1. for Standard:

      Install the bumper cover Click here.

    2. w/ Towing Hitch:

      Install the bumper cover Click here.

    3. w/ Pintle Hook:

      Install the bumper cover Click here.

  10. INSTALL REAR QUARTER PANEL MUDGUARD RH

    A01ENPF

    1. Install the mudguard with the clip.

    2. Using a T30 "TORX" socket, install the 8 screws.