AUTOMATIC TRANSMISSION SYSTEM (for 3UR-FE), Diagnostic DTC:P0982, P0983

DTC Code DTC Name
P0982 Shift Solenoid "D" Control Circuit Low (Shift Solenoid Valve S4)
P0983 Shift Solenoid "D" Control Circuit High (Shift Solenoid Valve S4)

DESCRIPTION

Shifting from 1st to 6th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely. Also, the ECM stops sending current to the open or short circuited shift solenoid valve Click here.

DTC Code DTC Detection Condition Trouble Area
P0982 The ECM detects a short in the shift solenoid valve S4 circuit 2 times when shift solenoid valve S4 is operated (1 trip detection logic).

  • Short in shift solenoid valve S4 circuit

  • Shift solenoid valve S4

  • ECM
P0983 The ECM detects an open in the shift solenoid valve S4 circuit 2 times when shift solenoid valve S4 is not operated (1 trip detection logic).

  • Open in shift solenoid valve S4 circuit

  • Shift solenoid valve S4

  • ECM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S4 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S4 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S4 circuit.

When shift solenoid valve S4 is OFF, if its resistance is 100 kΩ or higher, the ECM determines there is an open in the shift solenoid valve S4 circuit Click here.

WIRING DIAGRAM

A01ENF6E12

INSPECTION PROCEDURE

Tech Tips

Shift solenoid valve S4 is turned ON/OFF normally when the shift lever is in D:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S4 OFF OFF OFF OFF ON ON

PROCEDURE


  1. INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S4)


    1. A01EPLNE36
      Text in Illustration
      *a

      Component without harness connected

      (No. 1 Transmission Wire)

      Disconnect the No. 1 transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      14 (S4) - Body ground 20°C (68°F) 11 to 15 Ω

    NG

    Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

    A01ERYUE94
    Text in Illustration
    *1 for LHD
    *2 for RHD
    *a

    Front view of wire harness connector

    (to ECM)

    1. Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      C53-5 (S4) - Body ground 20°C (68°F) 11 to 15 Ω
      for RHD
      Tester Connection Condition Specified Condition
      C54-5 (S4) - Body ground 20°C (68°F) 11 to 15 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE ECM Click here

  3. INSPECT SHIFT SOLENOID VALVE S4


    1. A01EOSPE04
      Text in Illustration
      *a

      Component without harness connected

      (Shift Solenoid Valve S4)

      Remove shift solenoid valve S4.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body 20°C (68°F) 11 to 15 Ω

    3. Apply battery voltage (12 V) to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition

      • Battery positive (+) → Shift solenoid valve S4 connector

      • Battery negative (-) → Shift solenoid valve S4 body

      		 Valve moves and makes an operating noise

    NG

    REPLACE SHIFT SOLENOID VALVE S4 Click here

    OK

    REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE Click here