Click here

РЕЛЕ ПРОВЕРКА БЕЗ СНЯТИЯ С АВТОМОБИЛЯ

Click here
Click here
  1. Click here

    INSPECT STARTER RELAY (ST)


    1. A0097X9E37

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  2. Click here

    INSPECT GLOW PLUG RELAY (GLOW)


    1. A0097X9E37

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  3. Click here

    INSPECT FUEL PUMP RELAY (FUEL PMP)


    1. A00993VE26

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  4. Click here

    INSPECT NO. 1 INTEGRATION RELAY (IG2)


    1. Check the IG2 fuse.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        IG2 fuse Always Below 1 Ω

        If the result is not as specified, replace the IG2 fuse.

    2. Check the IG2 relay.


      1. A00971WE01

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1H-4 Battery voltage not applied to terminals 1H-1 and 1H-3 10 kΩ or higher
        Battery voltage applied to terminals 1H-1 and 1H-3 Below 1 Ω
        Table 1. Text in Illustration
        *a

        Component without harness connected

        (Integration Relay)

        If the result is not as specified, replace the integration relay.

  5. Click here

    INSPECT NO. 1 INTEGRATION RELAY (EFI)


    1. Check the EFI fuse.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        EFI fuse Always Below 1 Ω

        If the result is not as specified, replace the EFI fuse.

    2. Check the EFI relay.


      1. A00971WE01

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1I-4 Battery voltage not applied to terminals 1I-2 and 1I-3 10 kΩ or higher
        Battery voltage applied to terminals 1I-2 and 1I-3 Below 1 Ω
        Table 2. Text in Illustration
        *a

        Component without harness connected

        (Integration Relay)

        If the result is not as specified, replace the integration relay.

  6. Click here

    INSPECT MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

    Note:

    The ACC relay and IG1 No. 1 relay are built into the main body ECU (driver side junction block).


    1. Inspect the ACC relay.


      1. A0099DOE01

        Measure the resistance according to the value(s) in the table below.

        Table 3. Text in Illustration
        *a

        Component without harness connected

        (Main Body ECU)

        		 - -
        Standard Resistance
        Tester Connection Condition Specified Condition
        2D-17 - 2K-1 Battery voltage not applied to terminals 2A-48 and 2D-4 10 kΩ or higher
        Battery voltage applied to terminals 2A-48 and 2D-4 Below 1 Ω

        If the result is not as specified, replace the main body ECU.

    2. Inspect the IG1 No. 1 relay.


      1. A0099DOE01

        Measure the resistance according to the value(s) in the table below.

        Table 4. Text in Illustration
        *a

        Component without harness connected

        (Main Body ECU)

        		 - -
        Standard Resistance
        Tester Connection Condition Specified Condition
        2A-31 - 2K-1 Battery voltage not applied to terminals 2A-52 and 2D-4 10 kΩ or higher
        Battery voltage applied to terminals 2A-52 and 2D-4 Below 1 Ω

        If the result is not as specified, replace the main body ECU.