FRONT WIPER MOTOR INSTALLATION


  1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY


    1. A01CCI2E01

      Install the wire harness.

    2. Secure the wire harness with a new clamp and cut off the end.

    3. A01CBVY

      Install the windshield wiper motor assembly with the 3 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
    4. A01CB35

      Connect the connector.

  2. INSTALL FRONT WIPER CRANK SUB-ASSEMBLY


    1. Connect the windshield wiper motor assembly connector.

    2. Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.

    3. Disconnect the windshield wiper motor assembly connector.

    4. Temporarily install the front wiper crank sub-assembly on the windshield wiper motor assembly with the nut.

    5. Temporarily install the No. 1 rod on the crank arm pivot of the front wiper crank sub-assembly.

    6. Align the nut and crank arm pivot of the front wiper crank sub-assembly with the No. 1 rod as shown in the illustration.

      A01CDRTE01
    7. A01CFN7

      Tighten the front wiper crank sub-assembly with the nut.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }
    8. A01CEOT

      Apply MP grease to the crank arm pivot of the front wiper crank sub-assembly.

    9. A01CELK

      Connect the No. 1 rod to the crank arm pivot of the front wiper crank sub-assembly.

  3. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A01CFL4

      Install the windshield wiper motor and link assembly with the 3 bolts as shown in the illustration.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
    2. A01CAUN

      Connect the connector.

  4. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A01CEWQ

      Engage the 15 claws and 2 guides to install the cowl top ventilator louver sub-assembly as shown in the illustration.

    2. A01CFAO

      Install the 2 clips.

  5. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

    2. When reusing the front wiper arm and blade assembly RH:


      1. A01CC1NE01

        Clean the wiper arm serrations.

    3. When reusing the windshield wiper link assembly:


      1. A01CEI7E01

        Clean the wiper pivot serrations with a wire brush.

    4. A01CG9BE01

      Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  6. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. When reusing the front wiper arm and blade assembly LH:


      1. A01CC1NE01

        Clean the wiper arm serrations.

    2. When reusing the windshield wiper link assembly:


      1. A01CEI7E01

        Clean the wiper pivot serrations with a wire brush.

    3. A01CAPLE01

      Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

    4. Operate the front wipers while spraying washer fluid onto the windshield. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

  7. INSTALL WINDSHIELD WIPER ARM COVER


    1. A01CEUC

      Engage the 2 claws to install the 2 windshield wiper arm covers.