OUTER REAR VIEW MIRROR INSPECTION
-
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
-
Check the vertical and horizontal mirror motor operation.
-
Apply battery voltage and check the operation of the power mirror.
OK (w/ Memory) Measurement Condition Specified Condition Battery positive (+) → Terminal I2-1 (MV)
Battery negative (-) → Terminal I2-10 (M+)
Turns upward Battery negative (-) → Terminal I2-1 (MV)
Battery positive (+) → Terminal I2-10 (M+)
Turns downward Battery positive (+) → Terminal I2-9 (MH)
Battery negative (-) → Terminal I2-10 (M+)
Turns left Battery negative (-) → Terminal I2-9 (MH)
Battery positive (+) → Terminal I2-10 (M+)
Turns right OK (w/o Memory) Measurement Condition Specified Condition Battery positive (+) → Terminal I13-6 (MV)
Battery negative (-) → Terminal I13-5 (M+)
Turns upward Battery negative (-) → Terminal I13-6 (MV)
Battery positive (+) → Terminal I13-5 (M+)
Turns downward Battery positive (+) → Terminal I13-4 (MH)
Battery negative (-) → Terminal I13-5 (M+)
Turns left Battery negative (-) → Terminal I13-4 (MH)
Battery positive (+) → Terminal I13-5 (M+)
Turns right Text in Illustration *1 Component without harness connected
(Outer Rear View Mirror Assembly RH)
*2 w/ Memory *3 w/o Memory - - If the result is not as specified, replace the outer rear view mirror assembly RH.
-
-
Check the mirror heater (w/ Mirror Heater).
-
Text in Illustration *1 Component without harness connected
(Outer Rear View Mirror Assembly RH)
Measure the resistance according to the value(s) in the table below.
Standard Resistance Tester Connection Condition Specified Condition I2-2 (+) - I2-12 (-) 25°C (77°F) 3.2 to 6.9 Ω If the result is not as specified, replace the outer rear view mirror assembly RH.
-
-
-
INSPECT OUTER MIRROR RETRACTOR RH
-
Check the power retractable mirror motor operation.
-
For each mirror position: Disconnect the battery, set the mirror to each position by hand, connect the battery, and check the retractable mirror movement.
Note
-
Disconnect and reconnect the battery for each mirror position check.
-
The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
OK (w/ Memory) Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal I2-3 (MR)
Battery negative (-) → Terminal I2-11 (MF)
Forward position (A) Moves from (A) to retracted position (E) Battery negative (-) → Terminal I2-3 (MR)
Battery positive (+) → Terminal I2-11 (MF)
Forward position (A) Does not move Battery positive (+) → Terminal I2-3 (MR)
Battery negative (-) → Terminal I2-11 (MF)
Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery negative (-) → Terminal I2-3 (MR)
Battery positive (+) → Terminal I2-11 (MF)
Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal I2-3 (MR)
Battery negative (-) → Terminal I2-11 (MF)
Driving position (C) Moves from (C) to retracted position (E) Battery negative (-) → Terminal I2-3 (MR)
Battery positive (+) → Terminal I2-11 (MF)
Driving position (C) Does not move Battery positive (+) → Terminal I2-3 (MR)
Battery negative (-) → Terminal I2-11 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery negative (-) → Terminal I2-3 (MR)
Battery positive (+) → Terminal I2-11 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal I2-3 (MR)
Battery negative (-) → Terminal I2-11 (MF)
Retracted position (E) Does not move Battery negative (-) → Terminal I2-3 (MR)
Battery positive (+) → Terminal I2-11 (MF)
Retracted position (E) Moves from (E) to driving position (C) OK (w/o Memory) Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal I13-3 (MR)
Battery negative (-) → Terminal I13-9 (MF)
Forward position (A) Moves from (A) to retracted position (E) Battery negative (-) → Terminal I13-3 (MR)
Battery positive (+) → Terminal I13-9 (MF)
Forward position (A) Does not move Battery positive (+) → Terminal I13-3 (MR)
Battery negative (-) → Terminal I13-9 (MF)
Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery negative (-) → Terminal I13-3 (MR)
Battery positive (+) → Terminal I13-9 (MF)
Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal I13-3 (MR)
Battery negative (-) → Terminal I13-9 (MF)
Driving position (C) Moves from (C) to retracted position (E) Battery negative (-) → Terminal I13-3 (MR)
Battery positive (+) → Terminal I13-9 (MF)
Driving position (C) Does not move Battery positive (+) → Terminal I13-3 (MR)
Battery negative (-) → Terminal I13-9 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery negative (-) → Terminal I13-3 (MR)
Battery positive (+) → Terminal I13-9 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal I13-3 (MR)
Battery negative (-) → Terminal I13-9 (MF)
Retracted position (E) Does not move Battery negative (-) → Terminal I13-3 (MR)
Battery positive (+) → Terminal I13-9 (MF)
Retracted position (E) Moves from (E) to driving position (C) Text in Illustration *1 Component without harness connected
(Outer Rear View Mirror Assembly RH)
*2 w/ Memory *3 w/o Memory *4 (A) Forward Position *5 (B) *6 (C) Driving Position *7 (D) *8 (E) Retracted Position If the result is not as specified, replace the outer rear view mirror assembly RH.
-
-
-
-
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
-
Check the vertical and horizontal mirror motor operation.
-
Apply battery voltage and check the operation of the power mirror.
OK (w/ Memory) Measurement Condition Specified Condition Battery positive (+) → Terminal J2-1 (MV)
Battery negative (-) → Terminal J2-10 (M+)
Turns upward Battery negative (-) → Terminal J2-1 (MV)
Battery positive (+) → Terminal J2-10 (M+)
Turns downward Battery positive (+) → Terminal J2-9 (MH)
Battery negative (-) → Terminal J2-10 (M+)
Turns left Battery negative (-) → Terminal J2-9 (MH)
Battery positive (+) → Terminal J2-10 (M+)
Turns right OK (w/o Memory) Measurement Condition Specified Condition Battery positive (+) → Terminal J9-6 (MV)
Battery negative (-) → Terminal J9-5 (M+)
Turns upward Battery negative (-) → Terminal J9-6 (MV)
Battery positive (+) → Terminal J9-5 (M+)
Turns downward Battery positive (+) → Terminal J9-4 (MH)
Battery negative (-) → Terminal J9-5 (M+)
Turns left Battery negative (-) → Terminal J9-4 (MH)
Battery positive (+) → Terminal J9-5 (M+)
Turns right Text in Illustration *1 Component without harness connected
(Outer Rear View Mirror Assembly LH)
*2 w/ Memory *3 w/o Memory - - If the result is not as specified, replace the outer mirror view mirror assembly LH.
-
-
Check the mirror heater (w/ Mirror Heater).
-
Text in Illustration *1 Component without harness connected
(Outer Rear View Mirror Assembly LH)
Measure the resistance according to the value(s) in the table below.
Standard Resistance Tester Connection Condition Specified Condition J2-2 (+) - J2-12 (-) 25°C (77°F) 3.2 to 6.9 Ω If the result is not as specified, replace the outer rear view mirror assembly LH.
-
-
-
INSPECT OUTER MIRROR RETRACTOR LH
-
Check the power retractable mirror motor operation.
-
For each mirror position: Disconnect the battery, set the mirror to each position by hand, connect the battery, and check the retractable mirror movement.
Note
-
Disconnect and reconnect the battery for each mirror position check.
-
The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
OK (w/ Memory) Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal J2-3 (MR)
Battery negative (-) → Terminal J2-11 (MF)
Forward position (A) Moves from (A) to retracted position (E) Battery negative (-) → Terminal J2-3 (MR)
Battery positive (+) → Terminal J2-11 (MF)
Forward position (A) Does not move Battery positive (+) → Terminal J2-3 (MR)
Battery negative (-) → Terminal J2-11 (MF)
Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery negative (-) → Terminal J2-3 (MR)
Battery positive (+) → Terminal J2-11 (MF)
Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal J2-3 (MR)
Battery negative (-) → Terminal J2-11 (MF)
Driving position (C) Moves from (C) to retracted position (E) Battery negative (-) → Terminal J2-3 (MR)
Battery positive (+) → Terminal J2-11 (MF)
Driving position (C) Does not move Battery positive (+) → Terminal J2-3 (MR)
Battery negative (-) → Terminal J2-11 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery negative (-) → Terminal J2-3 (MR)
Battery positive (+) → Terminal J2-11 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal J2-3 (MR)
Battery negative (-) → Terminal J2-11 (MF)
Retracted position (E) Does not move Battery negative (-) → Terminal J2-3 (MR)
Battery positive (+) → Terminal J2-11 (MF)
Retracted position (E) Moves from (E) to driving position (C) OK (w/o Memory) Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal J9-3 (MR)
Battery negative (-) → Terminal J9-9 (MF)
Forward position (A) Moves from (A) to retracted position (E) Battery negative (-) → Terminal J9-3 (MR)
Battery positive (+) → Terminal J9-9 (MF)
Forward position (A) Does not move Battery positive (+) → Terminal J9-3 (MR)
Battery negative (-) → Terminal J9-9 (MF)
Between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery negative (-) → Terminal J9-3 (MR)
Battery positive (+) → Terminal J9-9 (MF)
Between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal J9-3 (MR)
Battery negative (-) → Terminal J9-9 (MF)
Driving position (C) Moves from (C) to retracted position (E) Battery negative (-) → Terminal J9-3 (MR)
Battery positive (+) → Terminal J9-9 (MF)
Driving position (C) Does not move Battery positive (+) → Terminal J9-3 (MR)
Battery negative (-) → Terminal J9-9 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery negative (-) → Terminal J9-3 (MR)
Battery positive (+) → Terminal J9-9 (MF)
Between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal J9-3 (MR)
Battery negative (-) → Terminal J9-9 (MF)
Retracted position (E) Does not move Battery negative (-) → Terminal J9-3 (MR)
Battery positive (+) → Terminal J9-9 (MF)
Retracted position (E) Moves from (E) to driving position (C) Text in Illustration *1 Component without harness connected
(Outer Rear View Mirror Assembly LH)
*2 w/ Memory *3 w/o Memory *4 (A) Forward Position *5 (B) *6 (C) Driving Position *7 (D) *8 (E) Retracted Position If the result is not as specified, replace the outer rear view mirror assembly LH.
-
-
-