OUTER REAR VIEW MIRROR REMOVAL


  1. REMOVE OUTER MIRROR GLASS


    1. A01CAUHE01

      Push in the upper side of the mirror surface to tilt it.

    2. Apply protective tape as shown in the illustration.

    3. A01CBU7E01

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.

      Note

      Do not pull the outer mirror RH with excessive force. Doing so may cause the actuator to come off or break the mirror surface.

    4. A01CF5LE01

      Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws as shown in the illustration.

    5. A01CBET

      Disconnect each connector, and remove the outer mirror RH.

  2. REMOVE OUTER MIRROR COVER


    1. A01CEZV

      Disengage the 2 claws as shown in the illustration.

    2. A01CCOR

      Pull the outer mirror RH in the direction indicated by the arrow and disengage the claw.

      Tech Tips

      If a claw is difficult to disengage, use a screwdriver with the tip wrapped in protective tape to disengage it.

    3. A01CBWIE01

      Pull the outer mirror cover RH and disengage the 3 claws in the order shown in the illustration.

    4. A01CBJG

      Pull the outer mirror cover RH in the direction indicated by the arrow in the illustration, disengage the 2 claws and remove the cover.

  3. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY


    1. A01CDJ3

      Remove the 2 screws.

    2. Disconnect the connector and remove the side turn signal light assembly.

  4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01CBQR

      Disengage the 2 clips and guide, and remove the front door lower frame bracket garnish.

  5. REMOVE LOWER DOOR FRAME GARNISH


    1. A01CFQ1

      Disengage the 3 clips and remove the lower door frame garnish.

  6. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01CDV8

      Using a moulding remover, disengage the 3 claws, and remove the front door inside handle bezel plug.

  7. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01CATKE01

      Using a moulding remover, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  8. REMOVE FRONT DOOR PULL HANDLE


    1. A01CBNYE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the claw and open the cover.

    2. A01CDYE

      Remove the screw.

    3. Disengage the 3 claws and remove the front door pull handle.

  9. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01CCX2

      Using a moulding remover, disengage the 9 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector.

  10. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01CC3Z

      Using a moulding remover, disengage the 9 claws.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  11. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01CGBP

      Remove the 2 screws.

    2. Using a clip remover, disengage the 12 clips.

    3. Pull out the front door trim board in the direction indicated by the arrow shown in the illustration.

    4. Raise the front door trim board and remove the front door trim board together with the front door inner glass weatherstrip.

    5. for Driver Side with Memory:


      1. Disconnect the connector.

    6. A01CBN8

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

  12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


    1. A01CCH4

      Disconnect the connector.

    2. Remove the 3 nuts.

    3. Disengage the claw and remove the outer rear view mirror assembly.