POWER MIRROR CONTROL SYSTEM (w/o Memory) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Mirror Selection SW (R) Mirror select switch signal for RH mirror / ON or OFF

      ON: Switch in R position

      OFF: Switch off or in L position

      		 -
      Mirror Selection SW (L) Mirror select switch signal for LH mirror / ON or OFF

      ON: Switch in L position

      OFF: Switch off or in R position

      		 -
      Mirror Position SW (R) Mirror adjust switch signal (right) / ON or OFF

      ON: Mirror adjust switch pressed right

      OFF: Mirror adjust switch not pressed right

      		 Check with the mirror select switch in except neutral position.
      Mirror Position SW (L) Mirror adjust switch signal (left) / ON or OFF

      ON: Mirror adjust switch pressed left

      OFF: Mirror adjust switch not pressed left

      		 Check with the mirror select switch in except neutral position.
      Mirror Position SW (Up) Mirror adjust switch signal (up) / ON or OFF

      ON: Mirror adjust switch pressed up

      OFF: Mirror adjust switch not pressed up

      		 Check with the mirror select switch in except neutral position.
      Mirror Position SW (Dwn) Mirror adjust switch signal (down) / ON or OFF

      ON: Mirror adjust switch pressed down

      OFF: Mirror adjust switch not pressed down

      		 Check with the mirror select switch in except neutral position.
      Outer Mirror Fold SW Outer mirror retractable switch signal / ON or OFF

      ON: Outer mirror retractable switch in retract position

      OFF: Outer mirror retractable switch in driving position

      		 -
      Auto Mirror SW Outer mirror retractable switch signal / ON or OFF

      ON: Outer mirror retractable switch in AUTO position

      OFF: Outer mirror retractable switch in except AUTO position

      		 -

    6. Enter the following menus: Body / Mirror / Data List.

    7. Read the Data List according to the display on the intelligent tester.

      Mirror
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RH Mir Position Sensor V Driver side mirror vertical sensor voltage / min: 0.49, max: 4.45 V Within range from 0.49 to 4.45 V -
      RH Mir Position Sensor H Driver side mirror horizontal sensor voltage / min: 0.49, max: 4.45 V Within range from 0.49 to 4.45 V -
      LH Mir Position Sensor V Passenger side mirror vertical sensor voltage / min: 0.49, max: 4.45 V Within range from 0.49 to 4.45 V -
      LH Mir Position Sensor H Passenger side mirror horizontal sensor voltage / min: 0.49, max: 4.45 V Within range from 0.49 to 4.45 V -
      ACC SW Engine switch ACC signal / ON or OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Mirror / Active Test.

    5. Perform the Active Test according to the display on the intelligent tester.

      Mirror
      Tester Display Test Part Control Range Diagnostic Note
      RH Mirror Up/Down Mirror vertical operation Up / OFF / Down -
      RH Mirror Right/Left Mirror horizontal operation Right / OFF / Left -
      LH Mirror Up/Down Mirror vertical operation Up / OFF / Down -
      LH Mirror Right/Left Mirror horizontal operation Right / OFF / Left -
      Mirror Fold Mirror retract operation ON / OFF -
      Mirror Return Mirror retract operation ON / OFF -