Click here

ION GENERATOR SWITCH REMOVAL

Click here
Click here Click here
  1. Click here

    REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL


    1. Operate the tilt lever to lower the steering wheel assembly.

    2. A01CDZ6E01

      Apply protective tape to the areas shown in the illustration.

    3. A01CBPO

      Disengage the 4 claws.

    4. A01CAPR

      Disengage the 7 claws and 2 guides to remove the No. 1 instrument cluster finish panel.

  2. Click here

    REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01CDHT

      Disengage the 4 claws.

    2. Disconnect the connector and remove the No. 1 instrument cluster finish panel garnish.

  3. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01CFFK

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and 2 guides.

    3. A01CE9QE01

      Disengage the 2 claws and disconnect the DLC3.

    4. Disengage the clamp.

    5. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  4. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A01CCYO

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and guide.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  5. Click here

    REMOVE COWL SIDE TRIM BOARD RH (for RHD)


    1. A01CFL6

      Remove the clip.

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board RH.

  6. Click here

    REMOVE COWL SIDE TRIM BOARD LH (for LHD)


    1. A01CCIK

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  7. Click here

    REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. A01CC18

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CC11

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CCKN

      Remove the 3 screws <B>.

    4. A01CCUJ

      Disengage the 14 claws and the 3 guides, and remove the lower instrument panel finish panel as shown in the illustration.

      Note:

      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  8. Click here

    REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)


    1. A01CF0E

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CCXK

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CGDM

      Disconnect the fuel filler opening lid lock sub-assembly and remove the fuel lid lock open lever sub-assembly.

    4. A01CCWL

      Remove the 3 screws <B>.

    5. A01CECJ

      Disengage the 13 claws, clip and the 3 guides and remove the lower instrument panel finish panel as shown in the illustration.

      Note:

      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  9. Click here

    REMOVE NO. 1 SWITCH HOLE BASE


    1. A01CFWGE01

      Disengage the 6 claws and 3 guides.

    2. Disconnect each connector and remove the No. 1 switch hole base.

  10. Click here

    REMOVE ION GENERATOR SWITCH (AIR PURIFIER SWITCH ASSEMBLY) (for RHD)


    1. A01CC0U

      Disengage the 2 claws and remove the ion generator switch (air purifier switch assembly).

  11. Click here

    REMOVE ION GENERATOR SWITCH (AIR PURIFIER SWITCH ASSEMBLY) (for LHD)


    1. A01CE3O

      Disengage the 2 claws and remove the ion generator switch (air purifier switch assembly).