REAR BLOWER MOTOR INSTALLATION


  1. INSTALL REAR BLOWER MOTOR SUB-ASSEMBLY


    1. A01CF3X

      Install the rear blower motor sub-assembly with the 3 screws.

    2. Connect each connector.

    3. Engage the clamp.

  2. INSTALL REAR NO. 2 SEAT TRACK ASSEMBLY RH


    1. A01CEV0

      Install the rear No. 2 seat track assembly RH with the 2 bolts and 2 nuts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  3. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH


    1. Connect the connectors.

    2. Engage the 2 guides, 7 claws and 14 clips to install the rear quarter trim panel assembly RH.

    3. Install the clip(A).

      A01CBNX

  4. INSTALL DECK SIDE GARNISH RH


    1. A01CC0RE01

      Engage the 4 guides and 11 claws to install the deck side garnish RH as shown in the illustration.

  5. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (for 60/40 Split Seat Type)


    1. A01CEZD

      Connect the floor end of the rear No. 1 seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  6. INSTALL INNER LUGGAGE COMPARTMENT TRIM COVER RH (for 60/40 Split Seat Type)


    1. A01CFS5

      Engage the 4 claws and install the inner luggage compartment trim cover RH.

  7. INSTALL ROPE HOOK ASSEMBLY (for RH Side)


    1. A01CB2D

      Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

    2. Engage the 2 claws.

  8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01CAW1

      Install the bolt.

    2. A01CAXYE01

      Push in the No. 1 luggage compartment trim and turn it clockwise approximately 90° to install the No. 1 luggage compartment trim hook.

  9. INSTALL REAR NO. 2 SEAT ASSEMBLY RH


    1. Temporary install the rear No. 2 seat assembly.

      Note

      Do not damage the rear No. 2 seat assembly, body or body interior.

    2. Connect the rear No. 2 seat outer belt assembly.

    3. A01CBYV

      Temporary tighten the 2 nuts.

    4. Lock the inner leg in the inner rail.

    5. A01CD6M

      Remove the clip of the seat track upper rail cover.

    6. A01CBU5

      Temporary install the seat track upper rail cover.

    7. Adjust the rear No. 2 seat assembly so that the positioning marks are aligned as shown in the illustration.

    8. A01CGJHE01

      As shown in the illustration, tighten the nut while pushing the rear No. 2 seat assembly towards the outside of the vehicle.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note


      • If this operation is difficult to perform alone, use two or more people.

      • Make sure not to misalign the positioning marks when pushing the seat.

      • If the nut is tightened without the seat pushed towards the outside of the vehicle, the inner lock may not operate normally.

    9. Remove the seat track upper rail cover.

    10. A01CBR7E01

      As shown in the illustration, tighten the nut while pushing the rear No. 2 seat assembly towards the outside of the vehicle, and install the rear No. 2 seat assembly.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note


      • If this operation is difficult to perform alone, use two or more people.

      • Make sure not to misalign the positioning marks when pushing the seat.

      • If the nut is tightened without the seat pushed towards the outside of the vehicle, the inner lock may not operate normally.

      • After reassembling the seat, check that the inner lock operates normally and that the inner lock and lock cover do not interfere with each other.

    11. Check that the rear No. 2 seat flips up and slides smoothly. If abnormal, loosen the 2 nuts and perform operations starting from step (f) again.

    12. A01CGCJE01

      Remove the 2 stopper bolts in the order indicated in the illustration.

      Note

      Before removing the stopper bolts, make sure that the inner leg is securely locked in the inner rail.

  10. INSTALL NO. 1 SEAT TRACK LOCK PLATE COVER (for RH Side)


    1. A01CDSK

      Engage the 2 claws and guide to install the No. 1 seat track lock plate cover.

  11. INSTALL UPPER SEAT TRACK RAIL COVER RH


    1. A01CFZ1

      Engage the 2 claws to install the grommet.

    2. A01CEBQ

      Install the clip of the seat track upper rail cover.

    3. A01CC1F

      Engage the 2 guides.

    4. Engage the 5 claws and clip to install the upper seat track rail cover.

  12. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


    1. A01CELJ

      Engage the claw to install the reclining adjuster release handle.

  13. INSTALL BACK DOOR SCUFF PLATE


    1. A01CCY0

      Engage the 2 guides, 4 clips and 4 claws to install the back door scuff plate.

  14. INSTALL BACK DOOR STRIKER COVER


    1. A01CEXU

      Engage the 2 guides and 4 claws to install the back door striker cover.

  15. CONNECT NO. 1 SLIDE DOOR WEATHERSTRIP RH


    1. A01CBO3E02
      Text in Illustration
      *1 Alignment Mark
      *a Pink
      *b White

      Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the No. 1 slide door weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  16. INSTALL REAR DOOR SCUFF PLATE RH


    1. Captain type rear seat:


      1. A01CFIB

        Engage the 2 guides, 9 clips and 9 claws to install the rear door scuff plate RH.

    2. Tip-up type rear seat:


      1. A01CETW

        Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.

      2. Engage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration.

      3. A01CEQB

        Using the slide lever, slide the rear No. 1 seat to the rearmost position.

      4. Engage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration to install the rear door scuff plate RH.

      5. A01CGAPE02
        Text in Illustration
        *1 Protective Tape

        Remove the protective tape applied to the bottom of the rear seat.