REAR NO. 2 SEAT OUTER BELT ASSEMBLY INSTALLATION

INSTALL UPPER ROOF SIDE INNER GARNISH LH (for LH Side)

1. 

   Engage the guide, claw and 2 clips to install the upper roof side inner garnish LH.

CONNECT POWER BACK DOOR ROD (w/ Power Back Door)

1. 

   Install the power back door rod with the 2 bolts.

   30 N*m

   306 kgf*cm

   22 ft.*lbf

INSTALL REAR WINDOW SIDE GARNISH LH (w/ Power Back Door)

1. 

   Engage the 3 clips and 2 claws to install the rear window side garnish LH.

INSTALL BACK DOOR NO. 2 SERVICE HOLE COVER (w/ Power Back Door)

1. 

   Engage the 3 claws to install the back door No. 2 service hole cover.

INSTALL BACK DOOR CENTER GARNISH (w/ Power Back Door)

1. 

   Engage the 6 clips and 4 claws to install the back door center garnish.

INSTALL UPPER ROOF SIDE INNER GARNISH RH (for RH Side)

1. 

   Engage the guide, claw and 2 clips to install the upper roof side inner garnish RH.

INSTALL REAR SEAT HOOK SUB-ASSEMBLY

1. 

   Engage the 2 guides as shown in the illustration.

2. 

   Engage the 4 claws.

3. 

   Install the rear seat hook sub-assembly RH with the 2 bolts.

INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH (for RH Side)

1. Connect the connectors.

2. Engage the 2 guides, 7 claws and 14 clips to install the rear quarter trim panel assembly RH.

3. 

   Install the clip(A).

INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH (for LH Side)

1. Engage the 2 guides, 8 claws and 15 clips, and install the rear quarter trim panel assembly LH.

2. 

   Install the clip(A).

INSTALL DECK SIDE GARNISH RH (for RH Side)

1. 

   Engage the 4 guides and 11 claws to install the deck side garnish RH as shown in the illustration.

INSTALL DECK SIDE GARNISH LH (for LH Side)

1. 

   Engage the 4 guides and 12 claws to install the deck side garnish LH as shown in the illustration.

CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY (for 60/40 Split Seat Type)

1. 

   Connect the floor end of the rear No. 1 seat outer belt assembly with the bolt.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

INSTALL INNER LUGGAGE COMPARTMENT TRIM COVER (for 60/40 Split Seat Type)

1. 

   Engage the 4 claws and install the inner luggage compartment trim cover RH.

INSTALL ROPE HOOK ASSEMBLY

1. 

   Install the rope hook assembly with the bolt.

   6.5 N*m

   66 kgf*cm

   58 in.*lbf

2. Engage the 2 claws.

INSTALL LUGGAGE COMPARTMENT TRIM HOOK

1. 

   Install the bolt.

2. 

   Push in the No. 1 luggage compartment trim and turn it clockwise approximately 90° to install the No. 1 luggage compartment trim hook.

INSTALL NO. 1 SLIDE DOOR WEATHERSTRIP

1. 

   Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the No. 1 slide door weatherstrip RH.

   Table 1. Text in Illustration

   *1	Alignment Mark
   *a	Pink
   *b	White

   Note:

   After installation, check that the corners fit correctly.

INSTALL REAR DOOR SCUFF PLATE

1. Captain type rear seat:

   
   
   1. 

      Engage the 2 guides, 9 clips and 9 claws to install the rear door scuff plate RH.

2. Tip-up type rear seat:

   
   
   1. 

      Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.

   2. Engage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration.

   3. 

      Using the slide lever, slide the rear No. 1 seat to the rearmost position.

   4. Engage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration to install the rear door scuff plate RH.

   5. 

      Remove the protective tape applied to the bottom of the rear seat.

      Table 2. Text in Illustration

      *1	Protective Tape

INSTALL BACK DOOR SCUFF PLATE

1. 

   Engage the 2 guides, 4 clips and 4 claws to install the back door scuff plate.

INSTALL BACK DOOR STRIKER COVER

1. 

   Engage the 2 guides and 4 claws to install the back door striker cover.

INSTALL REAR NO. 2 SEAT ASSEMBLY

1. Temporary install the rear No. 2 seat assembly.

   Note:

   Do not damage the rear No. 2 seat assembly, body or body interior.

2. Connect the rear No. 2 seat outer belt assembly.

3. 

   Temporary tighten the 2 nuts.

4. Lock the inner leg in the inner rail.

5. 

   Remove the clip of the seat track upper rail cover.

6. 

   Temporary install the seat track upper rail cover.

7. Adjust the rear No. 2 seat assembly so that the positioning marks are aligned as shown in the illustration.

8. 

   As shown in the illustration, tighten the nut while pushing the rear No. 2 seat assembly towards the outside of the vehicle.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

   Note:
   

   • If this operation is difficult to perform alone, use two or more people.

   • Make sure not to misalign the positioning marks when pushing the seat.

   • If the nut is tightened without the seat pushed towards the outside of the vehicle, the inner lock may not operate normally.

9. Remove the seat track upper rail cover.

10. 

    As shown in the illustration, tighten the nut while pushing the rear No. 2 seat assembly towards the outside of the vehicle, and install the rear No. 2 seat assembly.

    42 N*m

    428 kgf*cm

    31 ft.*lbf

    Note:
    

    • If this operation is difficult to perform alone, use two or more people.

    • Make sure not to misalign the positioning marks when pushing the seat.

    • If the nut is tightened without the seat pushed towards the outside of the vehicle, the inner lock may not operate normally.

    • After reassembling the seat, check that the inner lock operates normally and that the inner lock and lock cover do not interfere with each other.

11. Check that the rear No. 2 seat flips up and slides smoothly. If abnormal, loosen the 2 nuts and perform operations starting from step (f) again.

12. 

    Remove the 2 stopper bolts in the order indicated in the illustration.

    Note:

    Before removing the stopper bolts, make sure that the inner leg is securely locked in the inner rail.

INSTALL NO. 1 SEAT TRACK LOCK PLATE COVER

1. 

   Engage the 2 claws and guide to install the No. 1 seat track lock plate cover.

INSTALL UPPER SEAT TRACK RAIL COVER

1. 

   Engage the 2 claws to install the grommet.

2. 

   Install the clip of the seat track upper rail cover.

3. 

   Engage the 2 guides.

4. Engage the 5 claws and clip to install the upper seat track rail cover.

INSTALL RECLINING ADJUSTER RELEASE HANDLE

1. 

   Engage the claw to install the reclining adjuster release handle.