REAR NO. 1 SEAT INNER BELT ASSEMBLY (for Power Captain Seat) INSTALLATION


  1. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY


    1. A01CEBNE01

      Install the rear No. 1 seat inner belt assembly with the bolt and washer.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 1 seat inner belt assembly to overlap the protruding parts of the floor panel.

  2. INSTALL REAR SEAT CUSHION MOULDING


    1. A01CG8V

      Engage the 2 guides.

    2. Engage the 4 clips.

    3. Engage the 5 claws.

    4. Install the rear seat cushion moulding with the 2 bolts.

  3. INSTALL NO. 4 SEAT ADJUSTER COVER CAP


    1. A01CD9W

      Engage the guide and the claw to install the No. 4 seat adjuster cover cap.

  4. INSTALL NO. 3 SEAT ADJUSTER COVER CAP


    1. A01CDHW

      Engage the guide and the claw to install the No. 3 seat adjuster cover cap.

  5. INSTALL SEAT ADJUSTER COVER


    1. A01CC31

      Engage the 4 guides.

    2. Engage the 6 claws to install the seat adjuster cover cap LH.

  6. INSTALL NO. 1 SEAT ADJUSTER COVER CAP (for RH Side)


    1. A01CFWB

      Engage the 2 claws to install the 2 No. 1 seat side adjuster cover caps.

  7. INSTALL REAR SEAT SIDE TABLE (for RH Side)


    1. A01CB0P

      Install the rear seat side table with the 2 nuts and 2 bolts.

    2. A01CFTC

      Engage the hook to store the table.

    3. A01CG3R

      Secure the rear seat side table clip with the screw.

  8. INSTALL REAR SEAT SIDE TABLE BOARD (for RH Side)


    1. A01CCCU

      Engage the 6 clips to install the rear seat side table board.

  9. INSTALL NO. 2 SEAT ADJUSTER COVER CAP (for RH Side)


    1. A01CEPE

      Engage the 2 claws and the 2 guides to install the No. 2 seat side adjuster cover cap.

  10. INSTALL REAR SEAT SIDE TABLE COVER (for RH Side)


    1. A01CGAW

      Engage the guide and the claw to install the rear seat side table cover.

  11. INSTALL REAR NO. 1 SEAT ASSEMBLY


    1. Place the rear No. 1 seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Temporary install the rear No. 1 seat assembly with the 4 bolts.

    3. A01CCPRE01

      Install the rear No. 1 seat assembly with the 4 bolts.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

      Note

      Tighten the bolts in the order indicated in the illustration.

    4. Install the wiring harness protector set with the nut.

    5. Connect each connector.

    6. A01CDBN

      Engage the 6 claws to close the 2 covers as shown in the illustration.

    7. A01CFEU

      Engage the 6 claws to close the 2 covers as shown in the illustration.

  12. INSTALL REAR SEAT LEG COVER


    1. A01CEVN

      Engage the 5 claws and the guide to install the rear seat leg cover.

  13. INSTALL REAR SEAT LOWER CUSHION SHIELD


    1. A01CD5A

      Engage the claw and the guide to install the rear seat lower cushion shield as shown in the illustration.

  14. INSTALL REAR SEAT HEADREST ASSEMBLY

  15. INSPECT REAR NO. 1 SEAT ASSEMBLY


    1. Inspect the power seat operation Click here.