REAR NO. 2 SEAT OUTER BELT ASSEMBLY REMOVAL

ADJUST REAR NO. 2 SEAT ASSEMBLY
1. Adjust the rear No. 2 seat assembly so that the positioning marks are aligned as shown in the illustration.
REMOVE RECLINING ADJUSTER RELEASE HANDLE
1. Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
REMOVE UPPER SEAT TRACK RAIL COVER
1. Disengage the 5 claws and clip.
2. Disengage the 2 guides and remove the upper seat track rail cover.
3. Disengage the 2 claws and remove the grommet.
REMOVE NO. 1 SEAT TRACK LOCK PLATE COVER
1. Disengage the 2 claws, guide and remove the No. 1 seat track lock plate cover.
REMOVE NO. 2 SEAT HEADREST ASSEMBLY
REMOVE REAR SEAT CENTER HEADREST ASSEMBLY (for LH Side)

REMOVE REAR NO. 2 SEAT ASSEMBLY

Install the 2 stopper bolts in the order of <B>, <A>.

Torque:: 21 N*m { 214 kgf*cm, 16 ft.*lbf }

Note

Use service stopper bolts with part numbers 72702-58120 and 72702-58110, or other bolts of an equivalent size (M8 X 1.25).

Tech Tips

Stopper bolts sizes are as shown below.

Recommended Stopper Bolt
Part	Length
A	14 mm (0.551 in.)
B	15.5 mm (0.610 in.) or more
C	10 mm (0.394 in.) or less
D	72702-58110 Bolt <A>	45.7 mm (1.80 in.)
D	72702-58120 Bolt <B>	61.2 mm (2.41 in.)
E	72702-58110 Bolt <A>	27.7 mm (1.09 in.)
E	72702-58120 Bolt <B>	48.2 mm (1.90 in.)
F	18 mm (0.709 in.)
G	2.5 mm (0.0984 in.) or less
H	1.0 mm (0.0394 in.) or less
I	0.75 mm (0.0295 in.) or less
J	5.5 mm (0.217 in.)

Remove the 2 nuts and disconnect the rear No. 2 seat outer belt assembly.
Remove the rear No. 2 seat assembly.

Note

Do not damage the rear No. 2 seat assembly, body or body interior.

REMOVE BACK DOOR STRIKER COVER
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disengage the 4 claws and 2 guides, and remove the back door striker cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE BACK DOOR SCUFF PLATE
1. Remove the 4 claws, 4 clips and 2 guides, and remove the back door scuff plate.
REMOVE REAR DOOR SCUFF PLATE
1. Captain type rear seat:
  1. Disengage the 9 claws, 9 clips and 2 guides, and remove the rear door scuff plate RH.
2. Tip-up type rear seat:
  1. Text in Illustration
    
    *1 Protective Tape
    
    Apply protective tape to the bottom of the seat as shown in the illustration.
  2. Using the slide lever, slide the rear No. 1 seat to the rearmost position.
  3. Disengage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration.
    
    Note
    
    To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.
  4. Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.
  5. Disengage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration, and remove the rear door scuff plate RH.
    
    Note
    
    To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.
REMOVE NO. 1 SLIDE DOOR WEATHERSTRIP
REMOVE LUGGAGE COMPARTMENT TRIM HOOK
1. Turn the No. 1 luggage compartment trim hook clockwise approximately 90° and pull it out as shown in the illustration.
2. Remove the bolt and No. 1 luggage compartment trim hook.
REMOVE ROPE HOOK ASSEMBLY
1. Text in Illustration
  
  *1 Protective Tape
  
  Using a screwdriver, disengage the 2 claws.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Remove the bolt and the rope hook assembly.
REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER (for 60/40 Split Seat Type)
1. Disengage the 4 claws and remove the inner luggage compartment trim cover RH as shown in the illustration.
DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY (for 60/40 Split Seat Type)
1. Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.
REMOVE DECK SIDE GARNISH RH (for RH Side)
1. Disengage the 11 claws and 4 guides, and remove the deck side garnish RH as shown in the illustration.
REMOVE DECK SIDE GARNISH LH (for LH Side)
1. Disengage the 12 claws and 4 guides, and remove the deck side garnish LH as shown in the illustration.
REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH (for RH Side)
1. Remove the clip.
2. Disengage the 14 clips, 7 claws and 2 guides.
3. Disconnect the connectors, and remove the rear quarter trim panel assembly RH.
REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH (for LH Side)
1. Remove the clip.
2. Disengage the 15 clips, 8 claws and 2 guides, and remove the rear quarter trim panel assembly LH.
REMOVE REAR SEAT HOOK SUB-ASSEMBLY
1. Remove the 2 bolts.
2. Disengage the 4 claws.
3. Disengage the 2 guides and remove the rear seat hook sub-assembly RH as shown in the illustration.
DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY
1. Using a moulding remover, disengage the 2 claws and open the cover.
2. Loosen the bolt and disconnect the shoulder anchor of the rear No. 2 seat outer belt assembly.
REMOVE UPPER ROOF SIDE INNER GARNISH RH (for RH Side)
1. Disengage the 2 clips, claw and guide, and remove the upper roof side inner garnish RH as shown in the illustration.
REMOVE BACK DOOR CENTER GARNISH (w/ Power Back Door)
1. Using a moulding remover C, disengage the 6 clips and 4 claws, and remove the back door center garnish.
REMOVE BACK DOOR NO. 2 SERVICE HOLE COVER (w/ Power Back Door)
1. Disengage the 3 claws and remove the back door No. 2 service hole cover.
REMOVE REAR WINDOW SIDE GARNISH LH (w/ Power Back Door)
1. Disengage the 3 clips and 2 claws, and remove the rear window side garnish LH.
DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)
1. Remove the 2 bolts and disconnect the power back door rod.
REMOVE UPPER ROOF SIDE INNER GARNISH LH (for LH Side)
1. Disengage the 2 clips, claw and guide, and remove the upper roof side inner garnish LH as shown in the illustration.
REMOVE REAR NO. 2 SEAT OUTER BELT ASSEMBLY
1. Remove the bolt and rear No. 2 seat outer belt assembly.